Serpent Cobra GT
#933
There is a fuel filter inside the tank, that one should be more than adequate. As far as filters from the exhaust I personally don't run them but I have seen some people with them. I tried those inline fuel filters and they ultimately just give you one more area for a potential air leak making tuning lots of fun. Fresh tubing and the already installed filter should be solid. Look inside the tank you'll see the filter I am talking about I think its called a clunk filter.
#934
Tech Addict
If you can wait till tomorrow I can test the diff out and tell you how it fits. I have to head into work now.
#935
Tech Regular
iTrader: (2)
You will need a new clutch bell and I would use the center diff from the buggy. I just went and checked my buggy and the center drives are longer as well. 102 and 105. I would assume if you are using the buggy stuff you would need those as well.
If you can wait till tomorrow I can test the diff out and tell you how it fits. I have to head into work now.
If you can wait till tomorrow I can test the diff out and tell you how it fits. I have to head into work now.
Thanks!
Let me know what part numbers should i get for the GT to make like a buggy. (1 gear)
#936
Tech Addict
Are you wanting to run the center diff locked or with fluid? May be fun to try it with a functional center diff but that only adds to setup. We run very short tracks in Utah as well they make you drive no doubt.
What kind of motors are you running? I know a few short track monsters I use fro racing around here.
#938
Tech Addict
102mm for the center front driveshaft.
Differential cover for the buggy
The correct clutch bell. Not really sure what tooth depends on what you decide.
Looks like you may have to do a little shimming to get the single speed to fit nice and tight between the 2speed mounts as the differential is a little shorter than the 2speed by maybe 2-3mm.
Seems like it will work with the parts above but that is just my opinion. I'll post you a pic when I get back home.
#939
Tech Regular
iTrader: (2)
Okay so I have the one speed in my car. Looks like you are going to need...
102mm for the center front driveshaft.
Differential cover for the buggy
The correct clutch bell. Not really sure what tooth depends on what you decide.
Looks like you may have to do a little shimming to get the single speed to fit nice and tight between the 2speed mounts as the differential is a little shorter than the 2speed by maybe 2-3mm.
Seems like it will work with the parts above but that is just my opinion. I'll post you a pic when I get back home.
102mm for the center front driveshaft.
Differential cover for the buggy
The correct clutch bell. Not really sure what tooth depends on what you decide.
Looks like you may have to do a little shimming to get the single speed to fit nice and tight between the 2speed mounts as the differential is a little shorter than the 2speed by maybe 2-3mm.
Seems like it will work with the parts above but that is just my opinion. I'll post you a pic when I get back home.
I have a Speed in it, about the diff i prefer it to be with oil.
Thanks, i'll wait for the pic.
#940
Tech Addict
Sorry this took me so long... So much stuff going on for me right now lol.
So here is why I mentioned getting the longer front drive shaft.
Front = Right
The front driveshaft pins are too close to the end of the cup in my opinion. I would bump it up to the 102 and be safe. Other than that the parts I listed above should do the trick.
So here is why I mentioned getting the longer front drive shaft.
Front = Right
The front driveshaft pins are too close to the end of the cup in my opinion. I would bump it up to the 102 and be safe. Other than that the parts I listed above should do the trick.
#941
Tech Regular
iTrader: (2)
Sorry this took me so long... So much stuff going on for me right now lol.
So here is why I mentioned getting the longer front drive shaft.
Front = Right
The front driveshaft pins are too close to the end of the cup in my opinion. I would bump it up to the 102 and be safe. Other than that the parts I listed above should do the trick.
So here is why I mentioned getting the longer front drive shaft.
Front = Right
The front driveshaft pins are too close to the end of the cup in my opinion. I would bump it up to the 102 and be safe. Other than that the parts I listed above should do the trick.
Do you know the 102mm drive shaft part number?
#942
102mm 'bone'
An 'internet' question initially only hit on a '112mm' but a European site came up with (after translation)........102mm..........'center front V2 Serpent 811 2.0'..........(600509).
#943
Tech Addict
#944
Tech Fanatic
iTrader: (12)