R/C Tech Forums - Search Results
R/C Tech Forums

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory
Search: Posts Made By: malkie
Showing results 1 to 14 of 14
Search took 0.01 seconds.
Forum: Radio and Electronics
07-04-2023, 12:54 AM
Replies: 143
Views: 20,269
Posted By malkie

Many thanks StephenR, great data and good to hear...

Many thanks StephenR, great data and good to hear you are still pursuing the project, despite the hardware issues.
Forum: Radio and Electronics
07-02-2023, 11:32 AM
Replies: 143
Views: 20,269
Posted By malkie

Great work here..

Having discovered this thread rather late down the line, well done for all this work trilerian, great to see such complete comparative data, especially as you bought and paid for the motors yourself....
Forum: Electric On-Road
10-28-2022, 03:55 AM
Replies: 1,675
Views: 645,252
Posted By malkie

On my TT01 TC I placed a 2mm spacer inside the...

On my TT01 TC I placed a 2mm spacer inside the chassis tube to raise the battery post. Might need longer screws but I think it was OK.
Forum: Electric On-Road
07-09-2019, 01:47 PM
Replies: 713
Views: 509,876
Posted By malkie

How are your front tyres wearing? With 2.5 Camber...

How are your front tyres wearing? With 2.5 Camber I would expect the contact patch to be well over on the inside edge. Try 1.0 Camber, if you haven’t already.
Forum: Electric On-Road
02-11-2019, 10:59 AM
Replies: 3,205
Views: 994,454
Posted By malkie

surely if the wing downforce is applied to the...

surely if the wing downforce is applied to the chassis it can only affect the rear tyres by being transferred via the shock?
Forum: Electric On-Road
12-18-2018, 07:42 AM
Replies: 3,205
Views: 994,454
Posted By malkie

Since I already have the X-Ray one there is no...

Since I already have the X-Ray one there is no need to buy another just for the spool, saves even more!
Forum: Electric On-Road
12-17-2018, 11:51 AM
Replies: 3,205
Views: 994,454
Posted By malkie

Why the Associated Left Hub? Does the X-Ray one...

Why the Associated Left Hub? Does the X-Ray one not fit?
Forum: Electric On-Road
11-10-2018, 02:50 PM
Replies: 3,205
Views: 994,454
Posted By malkie

Jan Mathiesky stated on FB: Hi guys There are...

Jan Mathiesky stated on FB:
Hi guys
There are changes in material and production process of the axel (sic).

Maybe to cure leaks?
Forum: Electric On-Road
04-09-2012, 10:47 AM
Replies: 12,286
Views: 1,218,184
Posted By malkie

I bought some 3300 (30C) Li-po's for my TC3...

I bought some 3300 (30C) Li-po's for my TC3 because they weigh only about 230g, as opposed to the 300g of my Turnigy 5300's (35C). I then started to get some ESC shutdown issues with my Hobby Wing...
Forum: Radio and Electronics
02-26-2012, 11:07 AM
Replies: 12,554
Views: 1,878,059
Posted By malkie

What firmware are you running? Have you...

What firmware are you running?

Have you actually loaded the 508 firmware?

I had a problem with my HW Xtreme Stock switching to sensorless mode, no sign of 'cogging', but it was very slow....
Forum: Radio and Electronics
02-19-2012, 09:33 PM
Replies: 12,554
Views: 1,878,059
Posted By malkie

What does right hand amount mean?

What does right hand amount mean?
Forum: Radio and Electronics
01-09-2012, 01:27 PM
Replies: 12,554
Views: 1,878,059
Posted By malkie

I was ruunning my TC last weekend with a 13.5...

I was ruunning my TC last weekend with a 13.5 HobbyWing motor, final drive was about 6:1, I'm using 3300 Li-po's and I was only putting around 1500mAh back into them after a 5 minute run, usually...
Forum: Radio and Electronics
01-07-2012, 01:05 AM
Replies: 12,554
Views: 1,878,059
Posted By malkie

Post the FDR, software and Speedo settings you...

Post the FDR, software and Speedo settings you are using and someone might be able to offer some advice.

Try searching this thread for 13.5, there are plenty of set-ups here.
Forum: Electric On-Road
12-25-2011, 12:51 AM
Replies: 12,286
Views: 1,218,184
Posted By malkie

Try putting a drop of CA on the thread before you...

Try putting a drop of CA on the thread before you fit the screw/ball joint. Helps to keep the screw in place. Make sure none of it gets on the small bush or outside of the shoulder. It works for me,...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.