R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Community
Wiki Posts
Search
Search: Posts Made By: DragonDrop
Showing results 1 to 11 of 11
Search took 0.00 seconds.
05-10-2009, 11:40 PM
Replies: 2,324
Views: 501,879
Posted By DragonDrop

I just set the turnbuckles to whatever length i...

I just set the turnbuckles to whatever length i needed to get it to drive straight then I fine tuned it with my radio. Then I set up the EPA to 76 left and 96 right. But these numbers are all...
05-07-2009, 06:09 PM
Replies: 2,324
Views: 501,879
Posted By DragonDrop

No... It's not the part near the servo saver that...

No... It's not the part near the servo saver that is the problem. It is at the other end of the turnbuckle. the steering assembly hits the servo when screwed in normally.
05-07-2009, 05:39 PM
Replies: 2,324
Views: 501,879
Posted By DragonDrop

Finally got my post count up.... I can post some...

Finally got my post count up.... I can post some pics now...

http://64.128.14.168/tb03/DSC03560.jpg
It's still messy. I still have to cut and resolder the wires for the motor and the rest.
...
05-07-2009, 05:34 PM
Replies: 1,173
Views: 262,508
Posted By DragonDrop

I'd rather see it... :p

I'd rather see it... :p
05-07-2009, 05:09 PM
Replies: 30
Views: 1,904
Posted By DragonDrop

Novak.... I Biased :)

Novak.... I Biased :)
05-07-2009, 04:59 PM
Replies: 1,173
Views: 262,508
Posted By DragonDrop

This threads almost a month old.... Still no...

This threads almost a month old.... Still no official release date??? :confused:
05-07-2009, 04:54 PM
Replies: 18
Views: 1,905
Posted By DragonDrop

So what's the logic behind this? Just trying to...

So what's the logic behind this? Just trying to keep spammers off?
05-06-2009, 04:50 PM
Replies: 2,324
Views: 501,879
Posted By DragonDrop

I was able to make it fit but what I did was I...

I was able to make it fit but what I did was I had to buy new servo stays (GH Racing Alum Serv Mount for Axial Ax10). They are made out of Aluminimum and tall enough to screw through both holes on...
05-03-2009, 12:19 PM
Replies: 2,324
Views: 501,879
Posted By DragonDrop

I have the Tamiya carbon reinforced A parts...

I have the Tamiya carbon reinforced A parts (54098) and K parts (54099) and there is no weight savings that I can detect. I'll try and find a gram scale to test but I'm pretty sure there won't be...
05-02-2009, 09:18 PM
Replies: 2,324
Views: 501,879
Posted By DragonDrop

Oops sorry I can't post pics cause my low post...

Oops sorry I can't post pics cause my low post count... oh well... If you want to see it you can check the newbie section of drccent. look for "my new ride".
05-01-2009, 04:27 PM
Replies: 2,324
Views: 501,879
Posted By DragonDrop

I just got the 3Racing CF chassis yesterday for...

I just got the 3Racing CF chassis yesterday for my TB-03. It's pretty sweet. The chassis comes with a completely redesigned steering assembly. Also it comes with a metal motor mount. I already...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.