R/C Tech Forums - Search Results
R/C Tech Forums

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory
 
Page 1 of 2
1
2
Search: Posts Made By: antlockyer
Showing results 1 to 25 of 49
Search took 0.00 seconds.
Forum: Electric On-Road
01-27-2020, 09:09 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

Yes, it pretty much needs double what you would...

Yes, it pretty much needs double what you would normally run with 2 tubes.

Found a picture of my stock car from the last time I ran it. Was going through a low CoG phase
...
Forum: Electric On-Road
01-23-2020, 11:09 PM
Replies: 1,475
Views: 383,577
Posted By antlockyer

Run it like that, take out a side tube and run...

Run it like that, take out a side tube and run your wires under the top plate. Lower CG, neater, no sensor issues.
Forum: Electric On-Road
12-22-2019, 01:56 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

What screws are you using? I've got big Lunsford...

What screws are you using? I've got big Lunsford titanium ones on one car and a steel equivalent on the other and I've had zero motor moment even in open mod with a couple of big crashes.
Forum: Electric On-Road
05-09-2018, 09:15 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

Side links, steering knuckles, lower suspension...

Side links, steering knuckles, lower suspension arms, rear bearings. Also get some spare front springs and kingpin shims.
Forum: Electric On-Road
10-28-2017, 12:36 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

I put a little piece of something in the retainer...

I put a little piece of something in the retainer to keep it the same length each time.
Forum: Electric On-Road
10-24-2017, 01:01 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

Kingpin shims. Roche do them in a pack 0.1mm...

Kingpin shims. Roche do them in a pack 0.1mm 0.2mm and 0.3mm
Forum: Electric On-Road
10-11-2017, 02:08 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

It will work, several people I know run it and...

It will work, several people I know run it and love it.
Forum: Electric On-Road
07-24-2017, 02:32 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

I did a little modeling of different pistons and...

I did a little modeling of different pistons and oil on both shocks. Very informative and interesting (for me anyway lol).
Forum: Electric On-Road
07-23-2017, 12:54 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

I'll stick with this one until the new car comes....

I'll stick with this one until the new car comes. I was looking at the Yokomo setups and they are all over the place. Obviously the front end Madera huge difference to what they needed.

I'll...
Forum: Electric On-Road
07-22-2017, 03:23 PM
Replies: 1,475
Views: 383,577
Posted By antlockyer

Running JFT s35 all round. I've always stuck with...

Running JFT s35 all round. I've always stuck with the heavy centre setup thinking it Was giving me the on power steering I wanted. I'm just curious to see what going soft will do. First with the...
Forum: Electric On-Road
07-22-2017, 10:44 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

Thanks for the info. Gives some perspective to...

Thanks for the info. Gives some perspective to the new shock values. I'm going to try a couple of different shocks back to back. All significantly lighter than in running now (550cst 2 hole).
Forum: Electric On-Road
07-22-2017, 07:13 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

and you were running quite a hard oil on the old...

and you were running quite a hard oil on the old shock right? I was just sitting here playing with it and the difference in feel compared to my TC shocks is astonishing.
Forum: Electric On-Road
07-22-2017, 02:11 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

Anyone tried going to a much thinner oil or 4...

Anyone tried going to a much thinner oil or 4 hole piston on the dvs-w shock?
Forum: Electric On-Road
06-27-2017, 07:47 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

Got to be Naoto's worlds winning setup I would...

Got to be Naoto's worlds winning setup I would have thought. Depends on additive I guess.
Forum: Electric On-Road
06-24-2017, 03:58 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

Someone said that s foam is better than A in 90%...

Someone said that s foam is better than A in 90% of the cases the other 10% it's terrible. For ETS either works for me and on Speed tech I prefer A

The differences are small enough for me to not...
Forum: Electric On-Road
06-24-2017, 01:11 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

I tried a lot of tyre combos before the Euros....

I tried a lot of tyre combos before the Euros. Ended up with some super fast ones that I couldn't control. I like A and S and ZAC project too. 30 all round apart from s35.

Were you running spider...
Forum: Electric On-Road
06-22-2017, 01:40 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

Don't forget to check droop, my Xenon springs...

Don't forget to check droop, my Xenon springs were a lot shorter when new that a new AE spring but stayed pretty consistent length wise.
Forum: Electric On-Road
06-21-2017, 08:30 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

Brain is back in gear today. Lowering the...

Brain is back in gear today.

Lowering the car 1mm with an under bulkhead shim will slightly reduce camber gain and will raise the front roll centre making it more resistant to roll (like a stiffer...
Forum: Electric On-Road
06-20-2017, 07:25 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

Roll centre and camber gain is different...

Roll centre and camber gain is different depending on what method you use. I've not got the brain power to explain it right now :)
Forum: Electric On-Road
04-07-2017, 07:20 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

That's what the instructions say 2 in the hub...

That's what the instructions say 2 in the hub B10002 (flanged) on the outside B10003 (unflanged) on the inside then one (B10002 flanged) sitting on the very inside under the spur.
Forum: Electric On-Road
04-04-2017, 09:59 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

Thanks Mathijs, yes some good racing. I'll be at...

Thanks Mathijs, yes some good racing. I'll be at Masters of Foam. Not sure about the Euros depends if I can get there by car :)
Forum: Electric On-Road
04-04-2017, 04:24 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

Repost from Facebook. Just a few...

Repost from Facebook.


Just a few (million) words about my first visit to the 1/12th scale Euros. I had an advantage in that I'd been to Racing Arena Limburg last year and loved the place. I'd...
Forum: Electric On-Road
03-27-2017, 01:44 PM
Replies: 1,475
Views: 383,577
Posted By antlockyer

Yup, I like it. Plenty of on power steering....

Yup, I like it. Plenty of on power steering. Ollie also runs quite a hard front spring but that was too hard for me to drive. Might have been better with higher than club grip.
Forum: Electric On-Road
03-27-2017, 01:30 PM
Replies: 1,475
Views: 383,577
Posted By antlockyer

That's what I'm running too.

That's what I'm running too.
Forum: Electric On-Road
03-23-2017, 07:44 AM
Replies: 1,475
Views: 383,577
Posted By antlockyer

http://site.petitrc.com/reglages/roche/setuprapide...

http://site.petitrc.com/reglages/roche/setuprapidef1/F1_AlexanderStocker_SideSpringTip20170315/
Showing results 1 to 25 of 49
 
Page 1 of 2
1
2


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.