R/C Tech Forums - Search Results

Search: Posts Made By: stanleyw808

Showing results 1 to 9 of 9
Search took 0.00 seconds.

Forum: Nitro Off-Road

07-13-2016, 08:34 PM

Replies: 4,255

Team Associated RC8B3 Nitro Team Kit

Views: 1,300,617

Posted By stanleyw808

Hello Razathorn, Thank You for Your reply. ...

Hello Razathorn,

Thank You for Your reply. :)

You already can imagine that the Inside Upper Link Spot is "So Far" in from the Inside Arm Hinge Pin. Now, You could see that if You are using...

Forum: Nitro Off-Road

07-13-2016, 03:58 AM

Replies: 4,255

Team Associated RC8B3 Nitro Team Kit

Views: 1,300,617

Posted By stanleyw808

Hello Razathorn or Wayne, Do You notice that...

Hello Razathorn or Wayne,

Do You notice that when You are using the outer hole on the hub or longest link arrangement that the Upper Arm Length is actually longer than the lower Arm Length??

If...

Forum: Nitro Off-Road

06-22-2016, 08:55 PM

Replies: 4,255

Team Associated RC8B3 Nitro Team Kit

Views: 1,300,617

Posted By stanleyw808

Kakenballs, Thank You for Your reply. ...

Kakenballs,

Thank You for Your reply.

In my experience, even using bigger piston holes in the rear, using same viscosity of oil sometimes giving us a bit stiffer rear shock.

But if this is...

Forum: Nitro Off-Road

06-21-2016, 11:59 PM

Replies: 4,255

Team Associated RC8B3 Nitro Team Kit

Views: 1,300,617

Posted By stanleyw808

Kakenballs, I'm curious about Your Shock...

Kakenballs,

I'm curious about Your Shock Piston choices, Are You sure You are putting bigger Holes Piston at the Front Side of Your Shock? Or You were meant it backwards, 1.2 F and 1.3 R?
...

Forum: Nitro Off-Road

02-27-2016, 03:58 PM

Replies: 4,255

Team Associated RC8B3 Nitro Team Kit

Views: 1,300,617

Posted By stanleyw808

Hello Dyno Dan, Thanks again for Your...

Hello Dyno Dan,

Thanks again for Your explanation. In the TEKNO set-up guide, they are also mentioning about Front Drive Shaft Sweep angle when adjusting Front Arm Sweep Position. And to my...

Forum: Nitro Off-Road

02-26-2016, 07:13 AM

Replies: 4,255

Team Associated RC8B3 Nitro Team Kit

Views: 1,300,617

Posted By stanleyw808

Hello Dyno Dan, Thank You very much for Your...

Hello Dyno Dan,

Thank You very much for Your insight explanation about the Front Dog Bone Sweep angle.

So, In Cav's car set-up situation where the Front Arm moved 1mm to the front side thus...

Forum: Nitro Off-Road

02-25-2016, 08:52 PM

Replies: 4,255

Team Associated RC8B3 Nitro Team Kit

Views: 1,300,617

Posted By stanleyw808

Hello Dyno Dan, Could kindly explain more...

Hello Dyno Dan,

Could kindly explain more detail regarding the Front Driveshaft Sweep, what would be the effect for having less and more sweep to the dynamics of the car?

Cheerss.. :)

Forum: Nitro Off-Road

11-02-2015, 05:06 AM

Replies: 4,255

Team Associated RC8B3 Nitro Team Kit

Views: 1,300,617

Posted By stanleyw808

Hello Kakenballs, I am interested with Your...

Hello Kakenballs,

I am interested with Your mention about drilling Your Spur Gear. Did You use Carbide Drill Bit or just usual HSS Drill Bit?

Could You share some picture of Your work?
...

Forum: Nitro Off-Road

07-25-2015, 01:34 AM

Replies: 4,255

Team Associated RC8B3 Nitro Team Kit

Views: 1,300,617

Posted By stanleyw808

Hello ramatribudiman, If Your preloads are...

Hello ramatribudiman,

If Your preloads are suspiciously "a lot" compared to the other relatively same RC8B3, You might check if there is a bind in the suspension components.

Cheerss.. :)

Showing results 1 to 9 of 9