Wild Cherry

Got hold of Lrp America just now .

They are sending us a new 3.5 program to try ...

Later today will load the new firmware and let you guys know how it went .

Cridd

iTrader: (16)

3.5 updated from 3.3, new stuff.

Bill K

iTrader: (1)

Any news if this will be released to the public any time soon? I gather this is a beta build of the new software..

Thanks,
Bill

JDJamminX1

iTrader: (3)

This is only a beta software. I want to see if this helps fixes the problem on his particular ESC. I cannot say when this will be made public.

John Mora
LRP America CS Rep.

gearhead_22

iTrader: (10)

anyone using the lrp flow with an 3pk fasst system in 17.5 TC. the problem I am having is I can not get my brakes to come in smooth. they come in too much or they dont come in at all. I have rebinded over and over again. what setting are you putting the brake and alt at when binding?

joeymdz

iTrader: (13)

http://www.youtube.com/watch?v=Gl1QDeCgsrw

Hopefully this will solve your problem

Wild Cherry

yes ,

They are sending us the 3.5 to try ..
Will let you know how it goes when we try later this week end .
Still have to get Brown to E mail the File

John

will get him to E mail you later today .

gearhead_22

iTrader: (10)

thanks i will try when i get home.

gearhead_22

iTrader: (10)

went home for lunch and tried it and can not find that setting in my radio. I have a 3pk.

trutledge83

How do we get this 3.5 software I don't see it on the lrp website?

C.Borgia

While attempting to update my Flow Works Team's firmware, the following occurred:

2013-11-16 17:25:57,049 [AWT-EventQueue-0] INFO: File selected
2013-11-16 17:26:01,170 [SwingWorker-pool-1-thread-1] INFO: Starting update
2013-11-16 17:27:01,733 [SwingWorker-pool-1-thread-1] ERROR: Error during update.
cc.lrp.fwupdate1.c.l: Timeout while waiting for echo of block 7
at cc.lrp.fwupdate1.a.f.a(Unknown Source)
at cc.lrp.fwupdate1.a.f.b(Unknown Source)
at cc.lrp.fwupdate1.a.j.e(Unknown Source)

As I now try to complete the update, the firmware update tool gives me "Error Cannot establish connection to speed control!"

I've checked all of the connections and restarted my computer. I also tried another sensor wire. Can anyone offer help on getting this working?

mrlahey

Please offer your advice. I am running 21.5T Boosted. LRP Flow with a X12 21.5T Stock Spec. FDR is 4.0. Speed control running v5.0 with settings 0,3,3,3,6,3,3. End bell timing is horizontal insert. The problem I am having is the car slows down a bit after the first 2-3 laps, motor temp is about 75 degrees c. Any suggestions to what I have wrong?

JDJamminX1

iTrader: (3)

Please send email to [email protected]. We can then find a solution for you.

John Mora
LRP CS Rep.

JDJamminX1

iTrader: (3)

This has not been published yet, as it is only Beta right now.

John Mora
LRP America CS Rep.

Troy Carter

iTrader: (22)

I've not run boosted 21.5 but I would gear it closer to 5.5fdr and boost up if needed. I'm thinking that you are geared too low putting stress on the ESC causing it to slow very shortly.