Hobbywing Xerun V3
#526
Xerun 120A v3.1
#527
#528
LCD program box: V1.13_131106
Hardware version: HW310 V1.0
Database version: 140503
Car ESC: V3.1_121129_Beta
Hardware version: HOBBYWINGS_456_V2
Database version: 130814
#529
Tech Master
iTrader: (2)
I would try to reinstall the ESC firmware if possible.
When you are trying to get the ESC into calibration mode .. is everything hooked up? sensor wire, motor wires, etc - just curious.
#530
I believe the program box is up to V1.17 .. but will have to check and don't have my LCD box on hand (lent to a friend).
I would try to reinstall the ESC firmware if possible.
When you are trying to get the ESC into calibration mode .. is everything hooked up? sensor wire, motor wires, etc - just curious.
I would try to reinstall the ESC firmware if possible.
When you are trying to get the ESC into calibration mode .. is everything hooked up? sensor wire, motor wires, etc - just curious.
I already reinstall the ESC firmware 2 times successfully but still the same issue
#531
Tech Master
iTrader: (2)
Can you perhaps post a video of what your doing? (showing the connections, what lights are flashing or not)
What profile did you set the ESC to? What color light is on when you turn it on (without trying to calibrate)? flashing pattern?
#532
I've never seen a V3 HW ESC not want to enter calibration mode. Only HW exception was very early releases of the 1S Xerun with V1 blinky software.
Can you perhaps post a video of what your doing? (showing the connections, what lights are flashing or not)
What profile did you set the ESC to? What color light is on when you turn it on (without trying to calibrate)? flashing pattern?
Can you perhaps post a video of what your doing? (showing the connections, what lights are flashing or not)
What profile did you set the ESC to? What color light is on when you turn it on (without trying to calibrate)? flashing pattern?
#533
Just updated the software of the box with a _V3 version and now the box works again when connected to the ESC. Still I can't calibrate the ESC... When I start the ESC with my radio on, the green light is blinking and if I accelerate a little bit it becomes red and comes back to green immediately after and the motor is working well. But still when I try to push the power button a little bit of time, nothing happen, still the green light blinking. And if I stop pushing, the ESC switches off.
#534
Just updated the software of the box with a _V3 version and now the box works again when connected to the ESC. Still I can't calibrate the ESC... When I start the ESC with my radio on, the green light is blinking and if I accelerate a little bit it becomes red and comes back to green immediately after and the motor is working well. But still when I try to push the power button a little bit of time, nothing happen, still the green light blinking. And if I stop pushing, the ESC switches off.
Please send me an email to [email protected]
#535
Good news, this morning I could calibrate my ESC
I just plug in the battery cables with maintaining the power button pushed and I could do it. Don't ask me why. Thanks to all of you for your support.
I just plug in the battery cables with maintaining the power button pushed and I could do it. Don't ask me why. Thanks to all of you for your support.
#536
Angelo are you still in vacation in GR?
#537
#538
I didn't have the chance to meet you there.Maybe the next time you'll come .
#539
Hi Angelo,
I've just done the software update for my V3.1 esc with the "V3.2_140627_Beta" software and I'm rather surprised to see that the options to set the boost timing were removed (4B and following), the only thing I can tune now is the amount of boost I wanna have, compared to the previous version where we could select the Boost start and end rpm, the boost slope,...
Is that normal and why a such decision?
Anyway, I can't wait to try these new software on track!
Best regards,
G-rem
I've just done the software update for my V3.1 esc with the "V3.2_140627_Beta" software and I'm rather surprised to see that the options to set the boost timing were removed (4B and following), the only thing I can tune now is the amount of boost I wanna have, compared to the previous version where we could select the Boost start and end rpm, the boost slope,...
Is that normal and why a such decision?
Anyway, I can't wait to try these new software on track!
Best regards,
G-rem
#540
Hi Angelo,
I've just done the software update for my V3.1 esc with the "V3.2_140627_Beta" software and I'm rather surprised to see that the options to set the boost timing were removed (4B and following), the only thing I can tune now is the amount of boost I wanna have, compared to the previous version where we could select the Boost start and end rpm, the boost slope,...
Is that normal and why a such decision?
Anyway, I can't wait to try these new software on track!
Best regards,
G-rem
I've just done the software update for my V3.1 esc with the "V3.2_140627_Beta" software and I'm rather surprised to see that the options to set the boost timing were removed (4B and following), the only thing I can tune now is the amount of boost I wanna have, compared to the previous version where we could select the Boost start and end rpm, the boost slope,...
Is that normal and why a such decision?
Anyway, I can't wait to try these new software on track!
Best regards,
G-rem
Or maybe they've just been removed as most people set them way too low which just generates lots of heat and no extra power.