NEW HOBBYWING STOCK SUPERCHARGED SOFTWARE
Programming mode you need to use the 3 pin port not the rx cable as the 2.1 is programmed that way only the v3 you use the 3 pin programming port which is also used as an motor fan input if needed.
Hi Guys
Im still in Bangkok Thailand were we have had sone awsome results in open brushless with Nicholas lee from Singapore running our v3 and A Hara in mod .
Software versions 129 and 526 have also been submitted to roar fir approval.
I hope all of you are acheiving great results and have fun along the way .
Regards Angelo
PS any questions or tech help please email me at
[email protected] or [email protected]
Im still in Bangkok Thailand were we have had sone awsome results in open brushless with Nicholas lee from Singapore running our v3 and A Hara in mod .
Software versions 129 and 526 have also been submitted to roar fir approval.
I hope all of you are acheiving great results and have fun along the way .
Regards Angelo
PS any questions or tech help please email me at
[email protected] or [email protected]
Tech Apprentice
hi angelo, i send you an email for info on 8.5T. Thanks for help
Hi Guys
Im still in Bangkok Thailand were we have had sone awsome results in open brushless with Nicholas lee from Singapore running our v3 and A Hara in mod .
Software versions 129 and 526 have also been submitted to roar fir approval.
I hope all of you are acheiving great results and have fun along the way .
Regards Angelo
PS any questions or tech help please email me at
[email protected] or [email protected]
Im still in Bangkok Thailand were we have had sone awsome results in open brushless with Nicholas lee from Singapore running our v3 and A Hara in mod .
Software versions 129 and 526 have also been submitted to roar fir approval.
I hope all of you are acheiving great results and have fun along the way .
Regards Angelo
PS any questions or tech help please email me at
[email protected] or [email protected]
Please keep us posted on this.
For some of us... the timing on the approval process is very important.
Thanks
Tech Apprentice
Hi
Can the latest HW software be loaded in the SP GT2.0 Pro?
Can the latest HW software be loaded in the SP GT2.0 Pro?
Tech Initiate
V3.2 downgrade
Can anyone tell me how to downgrade v3.2 software to v3.1 I always get the message that cannot downgrade tanks.
Tech Fanatic
iTrader: (1)
Hey Guys
Looking for one more setup for a newbie.
Running a hw xtreme stock esc with hw 21.5t.
The class is boosted and turbo unsure on what fdr to run.
Any help be great
Thanks
Looking for one more setup for a newbie.
Running a hw xtreme stock esc with hw 21.5t.
The class is boosted and turbo unsure on what fdr to run.
Any help be great
Thanks
Hi angelo,
I use your esc for about 3 years, so far so good even from 2.1 to 3.1versions . But recently I got two defective , they are v3.0 and 3.1. Before the problem happpen they were running with a TP 4.0 motor with gear ratio of around 8.3 in 1/10 touring car. Both problems are no output to the motor or it need some pushing force to make the motor rotate but however, finally no response although changing with a brand new motor or sensor cable.
I am now using the V3.1 again, but my setup is a little bit change only. That is to reduce the drag barke from 20% to 5% only. It already run for one month and so far so good. Will the stronge drag brake force killed those escs? Would you please advise me what the approiate drag brake force should be use for the class of racing?
Thanks a lot!
I use your esc for about 3 years, so far so good even from 2.1 to 3.1versions . But recently I got two defective , they are v3.0 and 3.1. Before the problem happpen they were running with a TP 4.0 motor with gear ratio of around 8.3 in 1/10 touring car. Both problems are no output to the motor or it need some pushing force to make the motor rotate but however, finally no response although changing with a brand new motor or sensor cable.
I am now using the V3.1 again, but my setup is a little bit change only. That is to reduce the drag barke from 20% to 5% only. It already run for one month and so far so good. Will the stronge drag brake force killed those escs? Would you please advise me what the approiate drag brake force should be use for the class of racing?
Thanks a lot!
Tech Champion
iTrader: (4)
Hi angelo,
I use your esc for about 3 years, so far so good even from 2.1 to 3.1versions . But recently I got two defective , they are v3.0 and 3.1. Before the problem happpen they were running with a TP 4.0 motor with gear ratio of around 8.3 in 1/10 touring car. Both problems are no output to the motor or it need some pushing force to make the motor rotate but however, finally no response although changing with a brand new motor or sensor cable.
I am now using the V3.1 again, but my setup is a little bit change only. That is to reduce the drag barke from 20% to 5% only. It already run for one month and so far so good. Will the stronge drag brake force killed those escs? Would you please advise me what the approiate drag brake force should be use for the class of racing?
Thanks a lot!
I use your esc for about 3 years, so far so good even from 2.1 to 3.1versions . But recently I got two defective , they are v3.0 and 3.1. Before the problem happpen they were running with a TP 4.0 motor with gear ratio of around 8.3 in 1/10 touring car. Both problems are no output to the motor or it need some pushing force to make the motor rotate but however, finally no response although changing with a brand new motor or sensor cable.
I am now using the V3.1 again, but my setup is a little bit change only. That is to reduce the drag barke from 20% to 5% only. It already run for one month and so far so good. Will the stronge drag brake force killed those escs? Would you please advise me what the approiate drag brake force should be use for the class of racing?
Thanks a lot!
HiH
Ed
Tech Apprentice
Tech Champion
iTrader: (4)
Suspended
iTrader: (76)
Where can I find the latest software for the Juststock ESC?