4LikesNEW HOBBYWING STOCK SUPERCHARGED SOFTWARE
12-17-2012, 11:13 AM
12-17-2012, 08:02 PM
12-18-2012, 11:42 AM
I would run a FDR around 5
boost 40
rpm start 1,500
rpm end 12,000
boost by thr No
turbo 24
turbo activation Full Thr
turbo eng 12/0.1s
turbo disengage 6/0.1s
turbo delay 0.2s
boost & turbo linear
thr punch rate switch 50%
1st stage 20
2nd stage 30
keep an eye on temp
boost 40
rpm start 1,500
rpm end 12,000
boost by thr No
turbo 24
turbo activation Full Thr
turbo eng 12/0.1s
turbo disengage 6/0.1s
turbo delay 0.2s
boost & turbo linear
thr punch rate switch 50%
1st stage 20
2nd stage 30
keep an eye on temp
Last edited by Barry_Hughes; 12-18-2012 at 11:45 AM. Reason: correction
12-20-2012, 10:57 AM
Tech Rookie
Hi , searched but didn't find nothing conclusive ,
I have a Venom PRO Brushless 120A esc and it looks just like xerun 120a sd , but is green.
I've read in some posts in this forum that this Venom esc are the same as Hobbywing xerun 120A ,
is it true ??
and can I use the hobbywing lcd program box, and this supercharger firmware in the venom esc ??
I have a Venom PRO Brushless 120A esc and it looks just like xerun 120a sd , but is green.
I've read in some posts in this forum that this Venom esc are the same as Hobbywing xerun 120A ,
is it true ??
and can I use the hobbywing lcd program box, and this supercharger firmware in the venom esc ??
12-20-2012, 03:57 PM
Hi , searched but didn't find nothing conclusive ,
I have a Venom PRO Brushless 120A esc and it looks just like xerun 120a sd , but is green.
I've read in some posts in this forum that this Venom esc are the same as Hobbywing xerun 120A ,
is it true ??
and can I use the hobbywing lcd program box, and this supercharger firmware in the venom esc ??
I have a Venom PRO Brushless 120A esc and it looks just like xerun 120a sd , but is green.
I've read in some posts in this forum that this Venom esc are the same as Hobbywing xerun 120A ,
is it true ??
and can I use the hobbywing lcd program box, and this supercharger firmware in the venom esc ??
12-20-2012, 03:59 PM
Merry Xmas from the crew at hobbywing .
12-21-2012, 01:48 PM
Tech Master
iTrader: (90)
My bad HW 120amp ESC appears to work again on the bench with the v3.1 software v3_508_NoTiming software and NO reverse. I haven't tried it on the track or on a car.... but if you run into issues with your ESC and the new v3.2 software.... try v3.1 again (v3.2 didn't un-install v3.1 during it's installation).
Looks like I've had my first issue with a hobbywing ESC (HW Xerun 120a 1s ). The HW ESC Sensor port apperas to have gone bad right before my A-Main which I TQ'd. The ESC will power on but the ESC will not turn.
For troubleshooting, I have tried different sensor cables, unplugged the sensor cable all together (turns but cogs), rebound my TX to ESC, tried a different motors, and have even tried to reload the firmware without any success (both motors and sensor cables work perfectly with another ESC).
It was plugged in a TLR 22sct, 17.5 motor, 2s 65c rating battery, and I was able to complete both quals with success. When I powered on for the main... the motor would not start then my troubleshooting began. (version v3.2 software).
My HW lineup includes: Xerun 120a 1s, Xerun 120a v2.1, Xerun 60a v2.1, SCT-Pro
For troubleshooting, I have tried different sensor cables, unplugged the sensor cable all together (turns but cogs), rebound my TX to ESC, tried a different motors, and have even tried to reload the firmware without any success (both motors and sensor cables work perfectly with another ESC).
It was plugged in a TLR 22sct, 17.5 motor, 2s 65c rating battery, and I was able to complete both quals with success. When I powered on for the main... the motor would not start then my troubleshooting began. (version v3.2 software).
My HW lineup includes: Xerun 120a 1s, Xerun 120a v2.1, Xerun 60a v2.1, SCT-Pro
12-24-2012, 10:42 PM
Have the basic setup sheets been done yet? im after a starting point for a 21.5 on 930stock
12-24-2012, 11:08 PM
Can you please release a 1s version of the V3 speed control? It would be great to have a smaller controller than the current Xerun 1S with a built in booster BEC.
12-26-2012, 03:16 AM
12-26-2012, 06:54 AM
Tech Adept
Sorry if this has been asked before.
Are the Turnigy Trackstar Turbo ESCs (120A & 80A) copies of the V2 Hobbywings ESCs??
Can I use the Hobbywing Programming card and PC software on these two ESCs (the Trackstars).
Thanks.
Are the Turnigy Trackstar Turbo ESCs (120A & 80A) copies of the V2 Hobbywings ESCs??
Can I use the Hobbywing Programming card and PC software on these two ESCs (the Trackstars).
Thanks.
12-28-2012, 09:14 AM
12-29-2012, 07:30 AM
12-31-2012, 12:07 PM
Tech Adept
how do you get the software to the box from web site
12-31-2012, 01:14 PM
Using the cable provided with your esc, you hook it up to your computer and plug into the spot on programming box, and hook up your esc to the box(not needed if just upgrading the box)
Go to Hobbywing.com site and download the software for your computer, You will need a zip file extractor to open file, run the application software once unzipped and it will install....
Check HERE FOR LINK...its the link to hobbywing where you download the software and then click the Manual tab for instructions you can download on how to do so if your still not sure
Go to Hobbywing.com site and download the software for your computer, You will need a zip file extractor to open file, run the application software once unzipped and it will install....
Check HERE FOR LINK...its the link to hobbywing where you download the software and then click the Manual tab for instructions you can download on how to do so if your still not sure