Associated RC8T and possibly FT RC8.2E parts or cheap roller
#1
Associated RC8T and possibly FT RC8.2E parts or cheap roller
I have an RC8.2e RTR that I am looking to either replace or upgrade. So if you have any parts, let me know.
Also looking for an RC8T or RC8Te. Rollers preferred, cheap if possible, I dont mind stuff that needs work.
Let me know what you guys have, may consider a trade, so let me know what you would be looking for.
Also looking for an RC8T or RC8Te. Rollers preferred, cheap if possible, I dont mind stuff that needs work.
Let me know what you guys have, may consider a trade, so let me know what you would be looking for.
#2
I have a few new parts (carbon radio tray, carbon center diff plate and aluminum center mounts). $30 shipped
#4
1/4milecrazy,
I have a RC8T roller that I am willing to sell. I have a brand new chassis that I will ship with the roller. The chassis currently on the truck is worn thin at the very rear.
Here are some upgrades:
1) Comes with King Headz one piece motor mount
2) Comes with aluminum rear hubs
3) Mugen turnbuckles have been installed in the rear. This requires some slight trimming of the rear bulkhead which has already been taken care of. The Associated turnbuckles have plastic ends that bend very easily.
4) I will include 4 sets of front springs and 3 sets of rear springs, and I will provide the spring rates at the time of shipment.
5) I will include a Proline Bulldog body, painted copper, that was only run in one race.
6) I am using a Hot Bodies D8T fuel tank because I went through 2 Associated tanks that leaked air at the seam in the middle. The Hot Bodies tank requires an additional hole in the chassis to fit. It has not been drilled into the new chassis yet, but I could do it for you if you like.
I will also include all the Associated parts that I have (quite a bit).
I would like $250 shipped for the roller with body and spare parts.
For an additional $20 I will provide the flywheel, clutch, and clutch bell that I was using.
For an additional $15 I will provide the LiPO receiver pack I was using.
If you are interested then let me know ASAP and I can provide pictures when I get off of work tonight.
Thanks,
Justin
I have a RC8T roller that I am willing to sell. I have a brand new chassis that I will ship with the roller. The chassis currently on the truck is worn thin at the very rear.
Here are some upgrades:
1) Comes with King Headz one piece motor mount
2) Comes with aluminum rear hubs
3) Mugen turnbuckles have been installed in the rear. This requires some slight trimming of the rear bulkhead which has already been taken care of. The Associated turnbuckles have plastic ends that bend very easily.
4) I will include 4 sets of front springs and 3 sets of rear springs, and I will provide the spring rates at the time of shipment.
5) I will include a Proline Bulldog body, painted copper, that was only run in one race.
6) I am using a Hot Bodies D8T fuel tank because I went through 2 Associated tanks that leaked air at the seam in the middle. The Hot Bodies tank requires an additional hole in the chassis to fit. It has not been drilled into the new chassis yet, but I could do it for you if you like.
I will also include all the Associated parts that I have (quite a bit).
I would like $250 shipped for the roller with body and spare parts.
For an additional $20 I will provide the flywheel, clutch, and clutch bell that I was using.
For an additional $15 I will provide the LiPO receiver pack I was using.
If you are interested then let me know ASAP and I can provide pictures when I get off of work tonight.
Thanks,
Justin
#7
I have a RC8T brand new in the box, with almost enough parts to build 2 truggys, just as well as a used roller, I also have 3 buggy rollers let me know what your interested in. I live 20 minutes from Critters you can text me for pictures and any questions you have, 856 278 3813