Getting out Sale B5M/RM ready to race
#1
Getting out Sale B5M/RM ready to race
Like the title says. Done with RC Not willing to split at this point
B5M with B5RM conversion with ton of hop up
SLRC chassis (also have the stock chassis)
Exotec Ti front axles
AE aluminum rear hubs
Brass and aluminum C mounts
Aluminum D mount
Aluminum Front hinge pin brace
Aluminum Steering
Schelle Ceramic tranny bearings(3 gear)
3 and 4 gear trannys
2 Schelle slipper set ups
4 sets clay fronts (Chainlinks,Typos, Dirt Webs, Electrons)
4 set Clay rears ( 2 pr Chainlinks, Dirtwebs, Barcodes
Multiple bodies for each car.
Electronics
HW 3.1 Stock Spec
Airtronics MT4 with low profile waterproof servo(modded so the wire comes out the back)
Reedy motors (8.0 and 13.5)
Aeromodel Square pack
New LRP 4900 Outlaw shorty
Reedy wolfpack saddle
AMB 2 wire transponder
Icharger 306 (single port)
Schuurspeed power supply
Tools
MIP 2.0 and 2.5
Factory Team 5.0 and 7.0 nut drivers
Factory Team Hex set
Much More Pit lamp
Hakko Soldering Iron
Don't want to think what this all would go for but I'm sure its north of $1500
$1000 takes everything i have (I'm sure there are things i am forgetting)
Will deliver anywhere in Socal Shipping will need to be discussed. PM me and i will text pics.
Thanks for looking.
B5M with B5RM conversion with ton of hop up
SLRC chassis (also have the stock chassis)
Exotec Ti front axles
AE aluminum rear hubs
Brass and aluminum C mounts
Aluminum D mount
Aluminum Front hinge pin brace
Aluminum Steering
Schelle Ceramic tranny bearings(3 gear)
3 and 4 gear trannys
2 Schelle slipper set ups
4 sets clay fronts (Chainlinks,Typos, Dirt Webs, Electrons)
4 set Clay rears ( 2 pr Chainlinks, Dirtwebs, Barcodes
Multiple bodies for each car.
Electronics
HW 3.1 Stock Spec
Airtronics MT4 with low profile waterproof servo(modded so the wire comes out the back)
Reedy motors (8.0 and 13.5)
Aeromodel Square pack
New LRP 4900 Outlaw shorty
Reedy wolfpack saddle
AMB 2 wire transponder
Icharger 306 (single port)
Schuurspeed power supply
Tools
MIP 2.0 and 2.5
Factory Team 5.0 and 7.0 nut drivers
Factory Team Hex set
Much More Pit lamp
Hakko Soldering Iron
Don't want to think what this all would go for but I'm sure its north of $1500
$1000 takes everything i have (I'm sure there are things i am forgetting)
Will deliver anywhere in Socal Shipping will need to be discussed. PM me and i will text pics.
Thanks for looking.
Last edited by DG Designs; 09-03-2015 at 10:57 AM.
#7
Ready to look at splitting.
B5M with RM conversion and Sanwa servo modded with short wire and case coming out the back. Tons of hop ups $300
MT4 and receiver. $old
Icharger I306 (single channel) and Schuurspeed PS $old
Hobbywing 3.1 stock spec and programer. $75
Hakko Soldering Iron $50
Reedy Mach 2 and 13.5. $40 each
LRP Outlaw shorty. $old
Reedy Wolf Pack Saddle $25
Aero Model Square $40
Tracpower 3250 $30
Prices listed are not including shipping. That will be discussed based on destination.
PM me and i will text pics
B5M with RM conversion and Sanwa servo modded with short wire and case coming out the back. Tons of hop ups $300
MT4 and receiver. $old
Icharger I306 (single channel) and Schuurspeed PS $old
Hobbywing 3.1 stock spec and programer. $75
Hakko Soldering Iron $50
Reedy Mach 2 and 13.5. $40 each
LRP Outlaw shorty. $old
Reedy Wolf Pack Saddle $25
Aero Model Square $40
Tracpower 3250 $30
Prices listed are not including shipping. That will be discussed based on destination.
PM me and i will text pics
Last edited by DG Designs; 09-09-2015 at 07:14 AM.
#12
is the B5M still available?
#14
pm sent