Fully Rebuilt and Restored Full Custom $1,800 Wraith MUST SEE!!
#1
Fully Rebuilt and Restored Full Custom $1,800 Wraith MUST SEE!!
PAYPAL ONLY! CONUS ONLY! NO TRADES!!! SERIOUS BUYERS ONLY!!
This Wraith was the original kit version released years ago. Since that time it has been torn down and rebuilt twice. New hardware, new upgrades for chassis rigidity, fast back mod, real hand formed aluminum opening hood polished to match the bright aluminum panels and roof. Polished panels were done by DMG. Nobody has a set of them! Hood was done by ScaleReady full aluminum…as far as I know Phillip Hepp only made 2 of these.
Sold!
Sold!
Sold!
I COMPLETELY STRIPPED THIS RIG TO THE BARE BONES AND REBUILT IT LAST MONTH WITH A TEAM FAST EDDY WRAITH BEARING KIT. ALL WORN OR NEARLY WORN BEARINGS THROWN OUT. THE REST OF THEM WERE REPLACED SINCE I ORDERED THE FULL BEARING KIT. SOME BEARINGS WERE JUST TAKEN APART TO BE CLEANED AND RELUBED.
MOTOR/ESC WERE SENT TO HOLMES FOR COMPLETE REFRESH AND TESTING. THE HOLMES BRXL HAS BEEN REPOXY AND A NEW CASE HAS BEEN INSTALLED TO IT. MOTOR HAS NEVER EVEN BEEN BROKEN IN YET!!
SHOCKS AND ALL INTERNALS ON THE AXLE AND TRANSMISSION HAVE ALSO BEEN COMPLETELY TORN DOWN, CLEANED, AND REBUILT METICULOUSLY!!
THIS RIG IS BASICALLY BACK TO BRAND NEW CONDITION!!
Front and rear LED's all work and will be included. All are Axial string LED's to their light controllers. Battery and electronics tray relocated under the hood up front.
Axles:
Front axle: Hot Racing SHD Locker with Axial HD OD gears up front with Wraith universals. Also steering arms are upgraded with Egressor's thick extended arms.
-Axial aluminum clockable C hubs for Wraith
-Axial aluminum XR knuckles
Rear axles: Hot Racing SHD Locker with Axial HD beveled stock ratio gears in the back with GPM black aluminum rear lock outs.
-All bearings just replaced with new Team Fast Eddy.
Transmission:
Wraith MIP drivelines
32p conversion
65T Mod 0.8 Gen3 Robinson Steel Slipper
SuperShafty's Beefy Output Shaft to run the Gen3 Slipper
Hot Racing Black Aluminum Wraith Tranny Housing
LOADED Robinson Hardened Steel Axial Tranny Internal Gears
14T 32p Robinson Racing Hardened Steel Pinion Gear
New Team Fast Eddy Bearings Used to Rebuild the Tranny
Tranny completely torn down, cleaned, and regreased LAST MONTH!
NEVER RAN AGAIN AFTER REBUILD!!
Wheels/foams:
2.2" KMC XD-795 Black Anodized Respun bead locks no scratches plus spare VP hardware
CI Foams front are DD Firm inner Soft outer. Rears are also DD's Firm Inner Medium outer.
Suspension/Links:
-NEWLY Rebuilt Losi Comp Crawler 4" shocks on Losi Whites Front. Vaterra 4" Black Springs Rears. If you want the old Losi Whites I can include them for you as well free. Built with Green Slime and Associated 40wt oil front and rear.
-Steering drag link and tie rod are Vanquish Titanium w/Revo Rod ends.
-Lower bent high clearance links are all BMRC Titanium links w/Revo Rod ends.
-Upper links are also BMRC Titanium links w/Revo Rod ends.
Electronics/Lighting:
-Holmes BRXL Waterproof (Recently sent into Holmes for re-epoxy and check up). Recently installed after the service and NEVER RAN!
-Castle 10A BEC set at 7.4V Shrink Wrapped and waterproofed.
-Hitec 7950TH w/Robitronics Long Servo Arm
-Holmes TorqueMaster 35T Recently Rebuilt and NEVER RAN!
-Axial LED strings to run 4 white Lights up front
-4 Axial LED string for the rear modded Axial Exo taillight bar and 2 more red LED's in the taillight buckets below the chassis.
Thanks!!
Alex
This Wraith was the original kit version released years ago. Since that time it has been torn down and rebuilt twice. New hardware, new upgrades for chassis rigidity, fast back mod, real hand formed aluminum opening hood polished to match the bright aluminum panels and roof. Polished panels were done by DMG. Nobody has a set of them! Hood was done by ScaleReady full aluminum…as far as I know Phillip Hepp only made 2 of these.
Sold!
Sold!
Sold!
I COMPLETELY STRIPPED THIS RIG TO THE BARE BONES AND REBUILT IT LAST MONTH WITH A TEAM FAST EDDY WRAITH BEARING KIT. ALL WORN OR NEARLY WORN BEARINGS THROWN OUT. THE REST OF THEM WERE REPLACED SINCE I ORDERED THE FULL BEARING KIT. SOME BEARINGS WERE JUST TAKEN APART TO BE CLEANED AND RELUBED.
MOTOR/ESC WERE SENT TO HOLMES FOR COMPLETE REFRESH AND TESTING. THE HOLMES BRXL HAS BEEN REPOXY AND A NEW CASE HAS BEEN INSTALLED TO IT. MOTOR HAS NEVER EVEN BEEN BROKEN IN YET!!
SHOCKS AND ALL INTERNALS ON THE AXLE AND TRANSMISSION HAVE ALSO BEEN COMPLETELY TORN DOWN, CLEANED, AND REBUILT METICULOUSLY!!
THIS RIG IS BASICALLY BACK TO BRAND NEW CONDITION!!
Front and rear LED's all work and will be included. All are Axial string LED's to their light controllers. Battery and electronics tray relocated under the hood up front.
Axles:
Front axle: Hot Racing SHD Locker with Axial HD OD gears up front with Wraith universals. Also steering arms are upgraded with Egressor's thick extended arms.
-Axial aluminum clockable C hubs for Wraith
-Axial aluminum XR knuckles
Rear axles: Hot Racing SHD Locker with Axial HD beveled stock ratio gears in the back with GPM black aluminum rear lock outs.
-All bearings just replaced with new Team Fast Eddy.
Transmission:
Wraith MIP drivelines
32p conversion
65T Mod 0.8 Gen3 Robinson Steel Slipper
SuperShafty's Beefy Output Shaft to run the Gen3 Slipper
Hot Racing Black Aluminum Wraith Tranny Housing
LOADED Robinson Hardened Steel Axial Tranny Internal Gears
14T 32p Robinson Racing Hardened Steel Pinion Gear
New Team Fast Eddy Bearings Used to Rebuild the Tranny
Tranny completely torn down, cleaned, and regreased LAST MONTH!
NEVER RAN AGAIN AFTER REBUILD!!
Wheels/foams:
2.2" KMC XD-795 Black Anodized Respun bead locks no scratches plus spare VP hardware
CI Foams front are DD Firm inner Soft outer. Rears are also DD's Firm Inner Medium outer.
Suspension/Links:
-NEWLY Rebuilt Losi Comp Crawler 4" shocks on Losi Whites Front. Vaterra 4" Black Springs Rears. If you want the old Losi Whites I can include them for you as well free. Built with Green Slime and Associated 40wt oil front and rear.
-Steering drag link and tie rod are Vanquish Titanium w/Revo Rod ends.
-Lower bent high clearance links are all BMRC Titanium links w/Revo Rod ends.
-Upper links are also BMRC Titanium links w/Revo Rod ends.
Electronics/Lighting:
-Holmes BRXL Waterproof (Recently sent into Holmes for re-epoxy and check up). Recently installed after the service and NEVER RAN!
-Castle 10A BEC set at 7.4V Shrink Wrapped and waterproofed.
-Hitec 7950TH w/Robitronics Long Servo Arm
-Holmes TorqueMaster 35T Recently Rebuilt and NEVER RAN!
-Axial LED strings to run 4 white Lights up front
-4 Axial LED string for the rear modded Axial Exo taillight bar and 2 more red LED's in the taillight buckets below the chassis.
Thanks!!
Alex
Last edited by alexchen86; 09-07-2015 at 09:05 PM. Reason: Sold!