Lots of Stuff, take a look
#1
Lots of Stuff, take a look
I accept Paypal, and will Ship the day after payment is made. **
Only trade is a Like new Mamba Max Pro
First up is a ProLine GMC Topkick dually body. Was trimmed by the previous owner. $30shipped
Axial AE-2 ESC was used for a short period. * * ***SOLD****
HS-5245MG has the 645 control board mod. * *Servo was used twice when the original board fried, I installed the 645 board and it has been in my spare box since. * *Would make a Great LCC dig servo $25 shipped
VP Hurst dig w/Servo, driveshaft and Every other part needed to bolt it on and go, it may need and output bushing before long. *It didn't really bother me that much so I never worried with it. They are only about $3 from vp.
$80 shipped
DH FAB Yota/hilux 4 link truss. * BNIP here are the details http://www.scale4x4rc.org/forums/showthread.php?t=62741
$20shipped
Trinity P94 12x2 this thing will HAUL AZZ! * *And has torque to boot. Dual shunt brushes with half the life left.*
Fresh turn on the comm.
$23 shipped
***SOLD***
RC4WD Steelie hubs. *Two hex two pin.
The two hex are new, the pin style are close to it. * * The wheel nut got loose and let the pin slip in one of the pin style. $16 shipped
HPI E10 monster Drift car, everything is as it was when I opened the box. * it is 2.4 ghz btw with a 3 channel TX and RX*
I've replaced 3 of the plastic bushings in the rear diff with bearings because they got loose. ***SOLD***
Next up is a #28 (Davy Allison)*
JRL Race car. * * 1988 model and still works like new, the tires even look new.
All it needs is an old Band 1 *26.995 tx and a battery to drive it. * *I hooked it up and manually worked the speed control.
Could have newage electronics put in it and would probably be a blast!*
$$40shipped
Thanks for looking!
Only trade is a Like new Mamba Max Pro
First up is a ProLine GMC Topkick dually body. Was trimmed by the previous owner. $30shipped
Axial AE-2 ESC was used for a short period. * * ***SOLD****
HS-5245MG has the 645 control board mod. * *Servo was used twice when the original board fried, I installed the 645 board and it has been in my spare box since. * *Would make a Great LCC dig servo $25 shipped
VP Hurst dig w/Servo, driveshaft and Every other part needed to bolt it on and go, it may need and output bushing before long. *It didn't really bother me that much so I never worried with it. They are only about $3 from vp.
$80 shipped
DH FAB Yota/hilux 4 link truss. * BNIP here are the details http://www.scale4x4rc.org/forums/showthread.php?t=62741
$20shipped
Trinity P94 12x2 this thing will HAUL AZZ! * *And has torque to boot. Dual shunt brushes with half the life left.*
Fresh turn on the comm.
$23 shipped
***SOLD***
RC4WD Steelie hubs. *Two hex two pin.
The two hex are new, the pin style are close to it. * * The wheel nut got loose and let the pin slip in one of the pin style. $16 shipped
HPI E10 monster Drift car, everything is as it was when I opened the box. * it is 2.4 ghz btw with a 3 channel TX and RX*
I've replaced 3 of the plastic bushings in the rear diff with bearings because they got loose. ***SOLD***
Next up is a #28 (Davy Allison)*
JRL Race car. * * 1988 model and still works like new, the tires even look new.
All it needs is an old Band 1 *26.995 tx and a battery to drive it. * *I hooked it up and manually worked the speed control.
Could have newage electronics put in it and would probably be a blast!*
$$40shipped
Thanks for looking!
Last edited by Twisted Nuts; 08-10-2012 at 06:33 AM.