SC10 SKID PLATE LOOK!!!!!!!!
#16
Bout to drill holes and ship out the freebies hope yall enjoy!
#17
All skids shipped should have them Mon or Tues thanks again.
#18
R/C Tech Elite Member
iTrader: (248)
Got my plate in the mail Tuesday and was able to get some track time with it and I am impressed. This thing really nails down the front end. I have been hunting a setup for a while and had reverted back to the SC10 Factory Team setup and ran 3 packs through before putting the plate on. Then I put the plate on and ran another 5 packs through and there was a definite difference in the front end. It just felt planted. I had been having some wandering and tried weighting down the front end but I like this design better because the weight is lower. I was really driving on the knifes edge I felt like. The weight transfer of my truck was not as "glitchy" as it had been with weights on the servo and front bumper. There were not many people at the track today for practice but I showed it to as many as I could. I did not not have my transponder hooked up today either so no hard numbers but it felt good, now I just gotta dial in the back end. I am hoping to hit the track again this week and will try and get some more details numbers for ya'll. I would definitely give it a try fellas. I may try it on my B4.1 in the next few weeks and will be order a few more if I like it as much on the buggy.
#19
Got my plate in the mail Tuesday and was able to get some track time with it and I am impressed. This thing really nails down the front end. I have been hunting a setup for a while and had reverted back to the SC10 Factory Team setup and ran 3 packs through before putting the plate on. Then I put the plate on and ran another 5 packs through and there was a definite difference in the front end. It just felt planted. I had been having some wandering and tried weighting down the front end but I like this design better because the weight is lower. I was really driving on the knifes edge I felt like. The weight transfer of my truck was not as "glitchy" as it had been with weights on the servo and front bumper. There were not many people at the track today for practice but I showed it to as many as I could. I did not not have my transponder hooked up today either so no hard numbers but it felt good, now I just gotta dial in the back end. I am hoping to hit the track again this week and will try and get some more details numbers for ya'll. I would definitely give it a try fellas. I may try it on my B4.1 in the next few weeks and will be order a few more if I like it as much on the buggy.
#20
......
#21
Tech Champion
iTrader: (377)
I got mine last week ...wow ! It may not take first place in a beauty contest but this thing works. It is as basic and Spartan as it needs to be, and by the way...it DOES do the job it's supposed to. Fit is great with some bending that is required ,brings just enough weight below the servo area so you dont need to add those weights that fall off sometimes and it stabilizes the front end to a degree. Set up is still key and once you figure out the best way to set up your sc10 with this ad on...your all set. Price is amazingly cheap for what it does and it does keep the chassis from cracking in the ''weak'' spot that is just in front of the servo area. This is something that I would definitely buy if I had another sc10,B4 or even a T4. Great job and thanks again,I wish you much luck with this product. Pete.
#23
#25
#26
Hey guys don't be without a great tuning tool only 5 min to install.Also we are looking at adding screws to make this a kit for the B4,T4,&SC10 after listening to the advise of guys that tested it out!
#27
Bump..... For the best performing skid plate you will find!!!!!!!
#28
5 minute install onto the SC10 and it works great! I completely agree with Peter. The fit is great and it eliminated the need for the weights I usually have up front. At first the front was picking up some dirt but after a quick bend it is fitting perfectly. Definitely a great add-on for the SC10.
#29
Hit me up if you need that front grip I got it!