(ERCM) Extreme RC Mods Nitro pipe
#1
(ERCM) Extreme RC Mods Nitro pipe
This is a truggy style, side bleed, polished pipe with the "one piece" connector
Custom made by hand out of Stainless steel by Extreme RC Mods
Hands Down the best pipe you can get for your big block nitro engine
Used very little, light scuffs on the bottom
Comes with crt5 header, gaskets and springs,
ring made to hole spring on header because springs
have pulled through the header, the ring works much
better than hooking springs directly to the header
135 shipped obo
Custom made by hand out of Stainless steel by Extreme RC Mods
Hands Down the best pipe you can get for your big block nitro engine
Used very little, light scuffs on the bottom
Comes with crt5 header, gaskets and springs,
ring made to hole spring on header because springs
have pulled through the header, the ring works much
better than hooking springs directly to the header
135 shipped obo
#2
Tech Rookie
best pipe in the universe
#4
Not to be a prune, but can't you get these pipes brand new from ERC for $130 direct?
#5
Tech Rookie
From the website:
"This truggy side bleed variant is the same as the regular side bleed but with a relocated stinger designed to fit truggies. This pipe is suited for engine sizes of .21 and up. Raw finish pictured, also available polished. Most truggies should require left hand mount (pictured) but right hand mount is available on request.
$130.00
Options
Polished Finish - $5.00
By default, all ERCM pipes come with a natural raw steel finish. Due to high demand for the polished finish, a small fee has been added in order to cover additional equipment, materials and time.
One Piece Mount - $10.00
All pipes are available with an optional one piece mount for spring coupled in-line manifolds. Manifold, springs and gasket are not included. We recommend using an HPI gasket, part #87049 or a similarly thick gasket, as standard ones tend to be too flimsy."
---------------------
The basic ERCM pipe is 130, plus add 25 shipping from canada, and wait a month for it to be made.
This one is a delux model, comes with all the upgraded options; polished 5.00 and "one piece" mount 10.00 plus crt5 header and springs and gaskets that's at least another 40 bucks.
New this set up is over 200.00
135 is reasonable price to start at
"This truggy side bleed variant is the same as the regular side bleed but with a relocated stinger designed to fit truggies. This pipe is suited for engine sizes of .21 and up. Raw finish pictured, also available polished. Most truggies should require left hand mount (pictured) but right hand mount is available on request.
$130.00
Options
Polished Finish - $5.00
By default, all ERCM pipes come with a natural raw steel finish. Due to high demand for the polished finish, a small fee has been added in order to cover additional equipment, materials and time.
One Piece Mount - $10.00
All pipes are available with an optional one piece mount for spring coupled in-line manifolds. Manifold, springs and gasket are not included. We recommend using an HPI gasket, part #87049 or a similarly thick gasket, as standard ones tend to be too flimsy."
---------------------
The basic ERCM pipe is 130, plus add 25 shipping from canada, and wait a month for it to be made.
This one is a delux model, comes with all the upgraded options; polished 5.00 and "one piece" mount 10.00 plus crt5 header and springs and gaskets that's at least another 40 bucks.
New this set up is over 200.00
135 is reasonable price to start at
#7
Tech Rookie
Put this pipe on any BigBore nitro engine and open it up!
picco .26 .28, savage 4.6 5.9 or pretty much anything over .21
picco .26 .28, savage 4.6 5.9 or pretty much anything over .21