Complete truggy setup - Jammin, Novarossi, Li-pos, Starterbox, AKAs - Lots of pics!
06-06-2010, 10:17 AM
#1
Jammin Truggy partout - All my 1/8th stuff is for sale *no crap here*
The only reason I'm selling this truck is because 1/8th scale is dead in Utah. I started racing in AZ at the nitropit where there was a huge turnout and 1/8th scale was super popular. I moved back to Utah and there is no decent tracks within an hour and a half.
I completely rebuilt this truck for this season, there was a series that moved around to all the tracks within 3 hours once a month that I wanted to run but the guy that ran it doesn't want to run it this year. Series was called the Rocky Mountain Tour (RCMT) and Tony isn't going to run it this year. I've given up on 1/8th in Utah and would like to see this setup go to someone that could use it.
I'm still racing 1/10th electric offroad and I'm dabbling with onroad. I work at a hobby shop so my knowledge of the hobby is pretty good. I don't want any trades.
Truck recieved new shocks, motor, oils, AKA cityblocks, body, wing, clutch shoes and springs, bearings, diffs and some other stuff I'm sure I'm forgetting.
The novarossi has about 1/3gallon through it. It got about a quart of fuel for break in using the heat cycle method of break in. I then ran 5 tanks though the truck after the rebuild. 3 were practice at an indoor track (IRCR) and the other 2 were at an outside track (Blacksheep raceway). All other new stuff has 5 tanks on it.
The truck itself is a Jammin 1.5, It's a Jammin x1 crt with a BCE chassis. It's basically a jammin x2 with the jammin x1 mounts. It uses all current Jammin x2 parts. A jammin x2 chassis would bolt on directly with the x2 chassis braces.
The truck has:
Odonnel truggy shocks (super cheap to rebuild)
BCE chassis
All aluminum parts including hingepin holders, shocktowers, braces and plates
buggy bumper
Jammin JP-3 Pipe
2 large ofna fuel filters (hollow) and holder (alows time to self marshal)
Hitec 5998TG steering servo
JR ST126MG throttle servo
Protec lipo voltage regulator
Common sense RC Lipo reciever pack 1500mah
mugen mono motor mount
Novarossi N.21R motor
Dynamite clutch shoes with 1.0springs
White Jconecpts wing
New Jconcepts Body
Kyosho 5mm 17mm wheel adapters
0'' offset wheel mod (kyosho rod ends for the steering rods)
and some other stuff I'm sure I'm forgetting
Lots of extra stuff is included including:
Like new AKA cityblocks on 0 offset rulux wheels
75% goosebumps on 1/2" rulux wheels
50% goosebumps on 0" aka wheels
Jammin chrome top starter box wired for Lipo with deans
smc5200 2s lipo for box (2s works fine, 3s would be better)
2 glow starters
4 jammin hex adapters/nuts
various rod ends
servo spacers
wheelbase spacers
2 radio box lids
6 new wheel and diff bearings
12 new clutch bearings
1/2 of a new wing mount
1 diff case
5 small headder to pipe springs
5 exhaust gaskets
1 pipe mount
1 front body mount
2 cast steering blocks
1 front complete upper arm
1 set of e-clip hingepins
2 sets shock wrenches
3 extra diffs (1 like new)
some fuel line
1 new set of answer rc clutch shoes with 1.0 and 1.1 springs
5 cell 1400mah reciever pack batt
extra shock springs
3 rear arms
Now open to part-outs - Prices are shipped
$200 roller (with extra parts, including 3 spare diffs)
SOLD motor witch clutch and bell
$65 aka tires
$40 pipe
$20 jr servo
$60 both sets of goosebump tires
$SOLD OFNA chrometop starterbox
$30 Reciever lipo and regulator
Please PM me with questions. II have e-mail notification on to my cellphone for fast resonse. Asking $600 shipped for complete setup including insurace and delivery. Due to dollar ammount you're going to have to sign for this package because of the insurance. NO TRADES
Please see
http://smg.photobucket.com/albums/v9...iel/x15%20crt/
For the rest of the pictures and for the pictures of the extra stuff
Please note truck may have some wear and tear on it due to it being used. I think the front universals are pretty close to needing to be replaced.
I completely rebuilt this truck for this season, there was a series that moved around to all the tracks within 3 hours once a month that I wanted to run but the guy that ran it doesn't want to run it this year. Series was called the Rocky Mountain Tour (RCMT) and Tony isn't going to run it this year. I've given up on 1/8th in Utah and would like to see this setup go to someone that could use it.
I'm still racing 1/10th electric offroad and I'm dabbling with onroad. I work at a hobby shop so my knowledge of the hobby is pretty good. I don't want any trades.
Truck recieved new shocks, motor, oils, AKA cityblocks, body, wing, clutch shoes and springs, bearings, diffs and some other stuff I'm sure I'm forgetting.
The novarossi has about 1/3gallon through it. It got about a quart of fuel for break in using the heat cycle method of break in. I then ran 5 tanks though the truck after the rebuild. 3 were practice at an indoor track (IRCR) and the other 2 were at an outside track (Blacksheep raceway). All other new stuff has 5 tanks on it.
The truck itself is a Jammin 1.5, It's a Jammin x1 crt with a BCE chassis. It's basically a jammin x2 with the jammin x1 mounts. It uses all current Jammin x2 parts. A jammin x2 chassis would bolt on directly with the x2 chassis braces.
The truck has:
Odonnel truggy shocks (super cheap to rebuild)
BCE chassis
All aluminum parts including hingepin holders, shocktowers, braces and plates
buggy bumper
Jammin JP-3 Pipe
2 large ofna fuel filters (hollow) and holder (alows time to self marshal)
Hitec 5998TG steering servo
JR ST126MG throttle servo
Protec lipo voltage regulator
Common sense RC Lipo reciever pack 1500mah
mugen mono motor mount
Novarossi N.21R motor
Dynamite clutch shoes with 1.0springs
White Jconecpts wing
New Jconcepts Body
Kyosho 5mm 17mm wheel adapters
0'' offset wheel mod (kyosho rod ends for the steering rods)
and some other stuff I'm sure I'm forgetting
Lots of extra stuff is included including:
Like new AKA cityblocks on 0 offset rulux wheels
75% goosebumps on 1/2" rulux wheels
50% goosebumps on 0" aka wheels
Jammin chrome top starter box wired for Lipo with deans
smc5200 2s lipo for box (2s works fine, 3s would be better)
2 glow starters
4 jammin hex adapters/nuts
various rod ends
servo spacers
wheelbase spacers
2 radio box lids
6 new wheel and diff bearings
12 new clutch bearings
1/2 of a new wing mount
1 diff case
5 small headder to pipe springs
5 exhaust gaskets
1 pipe mount
1 front body mount
2 cast steering blocks
1 front complete upper arm
1 set of e-clip hingepins
2 sets shock wrenches
3 extra diffs (1 like new)
some fuel line
1 new set of answer rc clutch shoes with 1.0 and 1.1 springs
5 cell 1400mah reciever pack batt
extra shock springs
3 rear arms
Now open to part-outs - Prices are shipped
$200 roller (with extra parts, including 3 spare diffs)
SOLD motor witch clutch and bell
$65 aka tires
$40 pipe
$20 jr servo
$60 both sets of goosebump tires
$SOLD OFNA chrometop starterbox
$30 Reciever lipo and regulator
Please PM me with questions. II have e-mail notification on to my cellphone for fast resonse. Asking $600 shipped for complete setup including insurace and delivery. Due to dollar ammount you're going to have to sign for this package because of the insurance. NO TRADES
Please see
http://smg.photobucket.com/albums/v9...iel/x15%20crt/
For the rest of the pictures and for the pictures of the extra stuff
Please note truck may have some wear and tear on it due to it being used. I think the front universals are pretty close to needing to be replaced.
Last edited by aradaiel; 06-20-2010 at 06:12 PM.
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
