CC 2200 $110 shipped
03-09-2010, 12:11 PM
#1
CC 2200 $110 shipped
"SOLD/TRADED"
I bought this off ebay last week for $100 then I realized the MMM is $150 by itself. So I might as well buy a combo for $240 off the bay.
This is what the listing said:
"new never used only bench tested castle creations 2200kv motor...its the black motor that comes with the brushless e-revo/e-maxx.....in excellent condition...all sales final, i will ship anywhere however, international bidders will pay actual shipping...happy bidding
"
Pic from bay
http://cgi.ebay.com/ws/eBayISAPI.dll...=STRK:MEWNX:IT
Pic from my room of same motor attached.
I have not installed this motor so I have no idea of its condition but the guy I bought it from on the bay has very good feedback and said its in excellent condition!
$110 shipped
Will trade for a good steering servo for a truggy!
I have perfect feedback on the bay and on Traxxas. Names are richracer2 and Rich Racer respectively
I bought this off ebay last week for $100 then I realized the MMM is $150 by itself. So I might as well buy a combo for $240 off the bay.
This is what the listing said:
"new never used only bench tested castle creations 2200kv motor...its the black motor that comes with the brushless e-revo/e-maxx.....in excellent condition...all sales final, i will ship anywhere however, international bidders will pay actual shipping...happy bidding
"Pic from bay
http://cgi.ebay.com/ws/eBayISAPI.dll...=STRK:MEWNX:IT
Pic from my room of same motor attached.
I have not installed this motor so I have no idea of its condition but the guy I bought it from on the bay has very good feedback and said its in excellent condition!
$110 shipped
Will trade for a good steering servo for a truggy!
I have perfect feedback on the bay and on Traxxas. Names are richracer2 and Rich Racer respectively
Last edited by richracer2; 03-15-2010 at 10:57 AM. Reason: added feedback info
03-11-2010, 08:51 AM
#4
Price Drop
ttt
New price! $100 shipped
I will trade this cc 2200 for a good truggy servo, or 4s 25c minimum lipos.
If you dont trust me maybe you can trust this seller http://www.rctech.net/forum/r-c-item...ons-lipos.html thats a link to the guy I bought them off e-bay from he is hootie7159 on RcTech
New price! $100 shipped
I will trade this cc 2200 for a good truggy servo, or 4s 25c minimum lipos.
If you dont trust me maybe you can trust this seller http://www.rctech.net/forum/r-c-item...ons-lipos.html thats a link to the guy I bought them off e-bay from he is hootie7159 on RcTech
Last edited by richracer2; 03-11-2010 at 09:07 AM.
? Going to the bay Sat night/ Sunday morning...
03-12-2010, 08:23 AM
#6
trade
I have a brand new Hitec HS 7955-TG that I will trade you. Here are the specs. This is what I run in my MBX5T. These retail for $125.00
Control System: +Pulse Width Control 1500usec Neutral
Required Pulse: 4.8-6.0 Volt Peak to Peak Square Wave
Operating Voltage Range: 4.8-6.0 Volts
Operating Temperature Range: -20 to +60 Degree C (-68F to +140F)
Operating Speed (4.8V): 0.19 sec/60° at no load
Operating Speed (6.0V): 0.15 sec/60° at no load
Stall Torque (4.8V): 250oz/in. (18kg.cm)
Stall Torque (6.0V): 333oz/in. (24kg.cm)
Operating Angle: 45 Deg. one side pulse traveling 400usec
360 Modifiable: Yes
Direction: Clockwise/Pulse Traveling 1500 to 1900usec
Idle Current Drain (4.8V): 3mA at stop
Idle Current Drain (6.0V): 3mA at stop
Current Drain (4.8V): 200mA/idle and 2.0 amps at lock/stall
Current Drain (6.0V): 240mA/idle and 3.0 amps at lock/stall
Dead Band Width: 2usec
Motor Type: Coreless Carbon Brush
Potentiometer Drive: 6 Slider Indirect Drive
Bearing Type: Dual Ball Bearing MR106
Gear Type: Titanium Gears
Connector Wire Length: 7" (178mm)
Dimensions: 1.57" x 0.78"x 1.45" (40 x 20 x 37mm)
Weight: 2.29oz (65g
Control System: +Pulse Width Control 1500usec Neutral
Required Pulse: 4.8-6.0 Volt Peak to Peak Square Wave
Operating Voltage Range: 4.8-6.0 Volts
Operating Temperature Range: -20 to +60 Degree C (-68F to +140F)
Operating Speed (4.8V): 0.19 sec/60° at no load
Operating Speed (6.0V): 0.15 sec/60° at no load
Stall Torque (4.8V): 250oz/in. (18kg.cm)
Stall Torque (6.0V): 333oz/in. (24kg.cm)
Operating Angle: 45 Deg. one side pulse traveling 400usec
360 Modifiable: Yes
Direction: Clockwise/Pulse Traveling 1500 to 1900usec
Idle Current Drain (4.8V): 3mA at stop
Idle Current Drain (6.0V): 3mA at stop
Current Drain (4.8V): 200mA/idle and 2.0 amps at lock/stall
Current Drain (6.0V): 240mA/idle and 3.0 amps at lock/stall
Dead Band Width: 2usec
Motor Type: Coreless Carbon Brush
Potentiometer Drive: 6 Slider Indirect Drive
Bearing Type: Dual Ball Bearing MR106
Gear Type: Titanium Gears
Connector Wire Length: 7" (178mm)
Dimensions: 1.57" x 0.78"x 1.45" (40 x 20 x 37mm)
Weight: 2.29oz (65g
03-13-2010, 09:20 PM
#9
I thought we had a trade deal servo for motor.
Do we have a deal.
Do we have a deal.
03-13-2010, 10:56 PM
#10
HUH?? I would have to get pics of the actual servo you have, the link was cool but I wouldn't make a deal without seeing pics of the one you have for trade. I will call you tomorrow as promised. As i said in the pm I wouldnt be able to really talk on the phone till Sunday cause my Fridays and Saturdays are crazy busy... Shooting a pm right now to you!
This is what I said in the pm...
My name is Richard, call me my number is (xxx)xxx-xxxx Its a Washington State number I still have though I have since moved. I wont be able to ship till Monday, so that gives us a chance to talk first. Sunday will be best for me unless you call within the next 30 minutes because I am extremely busy on Friday nights and all day Saturdays till about 7 or 8 pm. Whats your number and a good time to call you?
This is what I said in the pm...
My name is Richard, call me my number is (xxx)xxx-xxxx Its a Washington State number I still have though I have since moved. I wont be able to ship till Monday, so that gives us a chance to talk first. Sunday will be best for me unless you call within the next 30 minutes because I am extremely busy on Friday nights and all day Saturdays till about 7 or 8 pm. Whats your number and a good time to call you?
Last edited by richracer2; 03-13-2010 at 11:13 PM. Reason: I misquoted what I said in pm. I never said I was just "interested."
03-14-2010, 07:46 AM
#12
here is a link to photobucket and pics of the servo
http://m699.photobucket.com/albums/s...BBIhCsGD5yo%3D
http://m699.photobucket.com/albums/s...BBIhCsGD5yo%3D
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
