Hopped up race Revo f/s ($3000 invested!!)
#1
Hopped up race Revo f/s ($3000 invested!!) REDUCED!
Well, I've thought about it long and hard, but its time to sell my revo 3.3 race truck. The truck is in like new condition, and has been extremely well looked after (I work at the LHS tuning and repairing these for a living!!) This truck comes with tons of spares, as well as the following upgrades (as well as some others I have likely forgotten)
- forward only conversion (I also have a center diff and rear brake as well)
- response tires on hurricane rims
- crime fighters mounted on dyed velocity 6 dish rims
- sweptback as well as stock arms
- aluminum turnbuckles
- aluminum pushrods
- close ratio 2-spd
- assorted springs (gold and orange installed)
- proline single servo conversion with traxxas heavy duty servo saver spring
- Trinity hi-flo pipe ( custom coated to match the custom chassis)
- O.S .18 tz-tx with less than a gallon through it
- Tekno rc throttle mount and fuel tank conversion
- Hellfire tank
- Hotbodies wing mount
- Proline wing
- Acer Racing Ceramic bearing set
- Rpm bumpers
- crowd pleazer body
- HPI airfilter
- Hitec 5955tg steering servo (333oz @ .15s !!!)
- Hitec 5925mg throttle servo (130oz @ .08s)
This truck is in like new condition, but I have decided to run Buggy and Truggy only this year. I am asking $800, or $650 without the servos, but am open to any reasonable offer.
Email me at [email protected] for additional pics
- forward only conversion (I also have a center diff and rear brake as well)
- response tires on hurricane rims
- crime fighters mounted on dyed velocity 6 dish rims
- sweptback as well as stock arms
- aluminum turnbuckles
- aluminum pushrods
- close ratio 2-spd
- assorted springs (gold and orange installed)
- proline single servo conversion with traxxas heavy duty servo saver spring
- Trinity hi-flo pipe ( custom coated to match the custom chassis)
- O.S .18 tz-tx with less than a gallon through it
- Tekno rc throttle mount and fuel tank conversion
- Hellfire tank
- Hotbodies wing mount
- Proline wing
- Acer Racing Ceramic bearing set
- Rpm bumpers
- crowd pleazer body
- HPI airfilter
- Hitec 5955tg steering servo (333oz @ .15s !!!)
- Hitec 5925mg throttle servo (130oz @ .08s)
This truck is in like new condition, but I have decided to run Buggy and Truggy only this year. I am asking $800, or $650 without the servos, but am open to any reasonable offer.
Email me at [email protected] for additional pics
Last edited by nitroholic381; 05-08-2007 at 06:40 PM.
#2
bump
#3
Any trades?
#4
trade
r u interested in 1/10th offroad gt2 or electric offroad t4 or touring
#5
The only trade I would be interested in is a truggy. I would also consider a partial trade on a new .21 or .28 engine though.
#7
Still for sale. I would strongly prefer to sell it, rather than trade.
#8
Well, the mob has spoken, new price $625, or $500 without the servos.
#9
Bump!
#10
Any reasonable offer will be accepted. If its not gone by tomorrow afternoon, then its going on ebay.
#11
C'mon you can trade me and get rid of it!!
#13
Then you are a very blind man. I added up (at the lhs where is work) what it would cost to build this truck, and it came to $2500, not including the spares the truck comes with, or the many parts I have replaced on the truck. if you have any further questions, either pm me, or keep them to yourself!
#15
I like it!!
I lke the deal but what would it take to get the servos as well!!