REVO TRADE FOR LST2
10-29-2006, 11:45 PM
#1
REVO TRADE FOR LST2
Up for trade is my revo if you EVER WANTED TO RACE this is the ticket.
There is a TON OF SPARES (check pics)
The essentials
1) REVO 3.3 converted from 2.5 have 2.5 chassis and two 3.3 Chassis
2) 3.3 ported polished WITH OS carb 11k 1/2 gallon very smooth and fast
3) THE VERY HARD TO COME BY, RD ALUMINIUM 8MM axle carriers with hardened axles
also comes with the wrench and a boat load of 10mm ss locknuts.
4) RD quickturn (they dont make it for the 3.3 chassis) Custom cut hardened steel shaft
5) CLUTCH AND FLYWHEEL IS 1/8 scale with 3 mugen teflon shoes
6) FOC with several sets of gears
7) Resonator single chamber pipe with OS header(stock setup included)
8) RB aircleaner (works spectacular)
9) trinity single servo setup aluminium arm
10)Jammin 150cc tank
11)Custom made radio and receiver box moves weight closer to the front 1600mah pack included
12)DACE 23mm hubs
13)lundsford turnbuckles (2 integy heavy duty turnbuckles in front) I also have the 2 lundsfords
for the front
14)Slayden steering mods also the custom rear skid made out of extra center skid plate
15)Hard Anodized Teflon pillow balls all around
16) 2 complete sets of 40 series tires belted one set 60% other set is 95%
17) 1 set maxx mulchers had about 8 minutes on loamy track 99%
18) 1 set crime fighters belted these are worn 20% is pushing it
19) 1 center diff filled with half 300k and half 500k (not installed)
20) 2 21 conversions
21) 3 NEW ORIGINAL FUEL TANKS
22) 1 OS 18tz about 3/4 gallon (carb is on 3.3) I have two 3.3 carbs one is used one is new
23) OS AA glow ignitor
24) 3.3 engine brace in package new
25) Traxxas Hard Anodized Teflon-Coated GTR Shocks with Titanium Nitride Shock Shafts
26) SSG throttle servo mount
I will not part it out/ one shot ALL gone
There is a TON more I have not mentioned Just look at the picks,You will need
a radio receiver and 2 servos, and a starter box ( I can include a custom starter
box if the right deal is made
also a hitec hs985mg for steering 172.20oz-in @ 6.0V .13sec).
I AM LOOKING FOR A LST2 I DONT NEED THE RADIO OR SERVOS
ONLY LST2 NOTHING ELSE
If you want to purchase it 500.00
Thanks
my email is [email protected]
There is a TON OF SPARES (check pics)
The essentials
1) REVO 3.3 converted from 2.5 have 2.5 chassis and two 3.3 Chassis
2) 3.3 ported polished WITH OS carb 11k 1/2 gallon very smooth and fast
3) THE VERY HARD TO COME BY, RD ALUMINIUM 8MM axle carriers with hardened axles
also comes with the wrench and a boat load of 10mm ss locknuts.
4) RD quickturn (they dont make it for the 3.3 chassis) Custom cut hardened steel shaft
5) CLUTCH AND FLYWHEEL IS 1/8 scale with 3 mugen teflon shoes
6) FOC with several sets of gears
7) Resonator single chamber pipe with OS header(stock setup included)
8) RB aircleaner (works spectacular)
9) trinity single servo setup aluminium arm
10)Jammin 150cc tank
11)Custom made radio and receiver box moves weight closer to the front 1600mah pack included
12)DACE 23mm hubs
13)lundsford turnbuckles (2 integy heavy duty turnbuckles in front) I also have the 2 lundsfords
for the front
14)Slayden steering mods also the custom rear skid made out of extra center skid plate
15)Hard Anodized Teflon pillow balls all around
16) 2 complete sets of 40 series tires belted one set 60% other set is 95%
17) 1 set maxx mulchers had about 8 minutes on loamy track 99%
18) 1 set crime fighters belted these are worn 20% is pushing it
19) 1 center diff filled with half 300k and half 500k (not installed)
20) 2 21 conversions
21) 3 NEW ORIGINAL FUEL TANKS
22) 1 OS 18tz about 3/4 gallon (carb is on 3.3) I have two 3.3 carbs one is used one is new
23) OS AA glow ignitor
24) 3.3 engine brace in package new
25) Traxxas Hard Anodized Teflon-Coated GTR Shocks with Titanium Nitride Shock Shafts
26) SSG throttle servo mount
I will not part it out/ one shot ALL gone
There is a TON more I have not mentioned Just look at the picks,You will need
a radio receiver and 2 servos, and a starter box ( I can include a custom starter
box if the right deal is made
also a hitec hs985mg for steering 172.20oz-in @ 6.0V .13sec).
I AM LOOKING FOR A LST2 I DONT NEED THE RADIO OR SERVOS
ONLY LST2 NOTHING ELSE
If you want to purchase it 500.00
Thanks
my email is [email protected]
10-30-2006, 07:38 AM
#2
bizz ump
10-30-2006, 05:50 PM
#3
to the top
10-31-2006, 06:28 AM
#4
come on, who wants to win mt class its as easy as buying this
10-31-2006, 08:25 AM
#5
WE HAVE A WINNER SOLD!!!!!!!!!!!!!!!!!
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
