FS: AB Modified Stage 2 TRX 3.3 Engine (Drop In Ready)
#1
FS: AB Modified Stage 2 TRX 3.3 Engine (Drop In Ready)
im going big block and i need to sell this to help buy the rest of the stuff i need.
Its a AB Mods Stage 2 Traxxas 3.3 Engine from my revo. Ive ran nothing but O'Donnell 30% Race fuel through it. The motor has always been tuned to perfection. Its never seen over 240 degrees on a Raytek temp gun.
I broke the motor in stock and ran 1 gallon through it to see if it would break so i could use the ERP warranty. Well it survived and ran great so i sent it off to AB Mods to have the Stage 2 Mod done. Ive ran a gallon through it since.
So all together its had 2 gallons ran through it. The motor still has alot of pinch and runs great. I ran nothing but McCoy MC-59 Plugs through it. Its on its 2nd plug, Its first was the stock Traxxas 3231. I alway put the Piston at Bottom dead center right after the motor was shut off.
Im including the full stock clutch assembly. Youll get the Clutch bell, clutch & Spring, clutch nut, flywheel, and the collet.
The motor has a pull start on it cause my EZ Start quit working about a half gallon after breakin.
Im also including my stock Revo pipe that has the stinger drilled out. The drilled stinger helps quite a bit. Its drilled out as far as you can go without sacrificing durability.
Here is a pic of the crank and sleeve after modding.
http://www.freewebs.com/abmods/AB4.jpg
Here is pics of what you get. Ill even take a video of it running if youd like.
Also this is how i ship motors. i wrap them in bubble wrap then vacuum seal them.
Its a AB Mods Stage 2 Traxxas 3.3 Engine from my revo. Ive ran nothing but O'Donnell 30% Race fuel through it. The motor has always been tuned to perfection. Its never seen over 240 degrees on a Raytek temp gun.
I broke the motor in stock and ran 1 gallon through it to see if it would break so i could use the ERP warranty. Well it survived and ran great so i sent it off to AB Mods to have the Stage 2 Mod done. Ive ran a gallon through it since.
So all together its had 2 gallons ran through it. The motor still has alot of pinch and runs great. I ran nothing but McCoy MC-59 Plugs through it. Its on its 2nd plug, Its first was the stock Traxxas 3231. I alway put the Piston at Bottom dead center right after the motor was shut off.
Im including the full stock clutch assembly. Youll get the Clutch bell, clutch & Spring, clutch nut, flywheel, and the collet.
The motor has a pull start on it cause my EZ Start quit working about a half gallon after breakin.
Im also including my stock Revo pipe that has the stinger drilled out. The drilled stinger helps quite a bit. Its drilled out as far as you can go without sacrificing durability.
Here is a pic of the crank and sleeve after modding.
http://www.freewebs.com/abmods/AB4.jpg
Here is pics of what you get. Ill even take a video of it running if youd like.
Also this is how i ship motors. i wrap them in bubble wrap then vacuum seal them.
#2
after looking around a bit it seems there are a few scammers out there. I want to assure you im not one by showing you my Ebay Feedback and i have Heatware.
http://feedback.ebay.com/ws/eBayISAP...brown7552&iid=
http://www.heatware.com/eval.php?id=41507
http://feedback.ebay.com/ws/eBayISAP...brown7552&iid=
http://www.heatware.com/eval.php?id=41507
#3
bump
#4
up, not looking for alot here guys.
#5
What is the price on this?
#6
100 OBO