R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Nitro On-Road > Onroad Nitro Engine Zone

Reply
 
Thread Tools Search this Thread
Old 03-28-2007, 02:37 PM   #1261
Tech Elite
 
dj apolaro's Avatar
 
Join Date: May 2005
Location: Miami, Fl.
Posts: 2,364
Default

Quote:
Originally Posted by rmdhawaii
That's a great tuning tip DJ. I'll have to add it to the engine KB.
Remeber thats is assuming that the motor is not coming in hot and idling high for that reason.
dj apolaro is offline   Reply With Quote
Old 03-28-2007, 02:39 PM   #1262
Tech Master
 
ziggy12345's Avatar
 
Join Date: Jun 2003
Location: West Midlands, UK
Posts: 1,596
Default

Quote:
Originally Posted by serpentpro28
Hi' Uriah i have a question on my 35plus21 full mods,everytime i stop the idle is too high and i't takes a while to goes down,unless if i hit the trottle once,looks like to the bottom is lean but i open it up' i'm loosing power' need ur help'
thanks
Or it could be the top too lean. As you come off power the crank is still full of the high end mixture and if its too lean it will idle high until it see the low end mixture. Try letting the engine idle for 10 secs then floor the throttle. If the engine take off clean the bottom end is OK and the top end lean, If its sluggish then fast the low end is rich and the top ok
__________________
Dedicated RC Car Speed Site

http://www.fast-rc.co.uk/forum/index.php

Sponsored by:
Norfolk and Chance
ziggy12345 is offline   Reply With Quote
Old 03-28-2007, 02:39 PM   #1263
Tech Elite
 
rmdhawaii's Avatar
 
Join Date: Feb 2006
Posts: 3,804
Trader Rating: 4 (100%+)
Default

Quote:
Originally Posted by dj apolaro
Remeber thats is assuming that the motor is not coming in hot and idling high for that reason.
Understood. I'll be sure to include this note as well.
__________________
Nitro Knowledge Base: http://nitrokb.netne.net
My YouTube Channel: http://www.youtube.com/nitrokb -> Lots of on-road nitro & eletric action + some off-road as well
My Flickr Photostream: http://www.flickr.com/photos/nitrokb/
Kyosho V-ONE RRR WC (x2) \ XRAY T2'007 \ Also owned: XRAY NT1 & Mugen MTX-4
rmdhawaii is offline   Reply With Quote
Old 03-28-2007, 06:12 PM   #1264
Tech Regular
 
serpentpro28's Avatar
 
Join Date: Aug 2002
Location: VA
Posts: 299
Default

Quote:
Originally Posted by Grinder
Hi. It could be that the low end is too rich still. Do you see lots of smoke out of the corners? You should see some. Try leaning the low end needle at the same time close the idle screw slightly. If it is better, then do it again. Just make sure to check your glowplug after each run to make sure it is not getting dry. It should look shiny.
Thanks Uriah i will try that' btw what is the good temperature after the brake-in?
Thanks to you 2 dj' for the info'
__________________
Team bilis racing
serpentpro28 is offline   Reply With Quote
Old 03-29-2007, 04:20 AM   #1265
Tech Rookie
 
Kazador's Avatar
 
Join Date: Mar 2007
Location: Czech rep.
Posts: 3
Default

Hi.I have JLR .12 Red Dot Engine. What type of glow plug is best for 16% nitro. I have PT6H Picco Plug, is it good for me?Thanks
Kazador is offline   Reply With Quote
Old 03-29-2007, 06:12 AM   #1266
Tech Master
 
Grinder's Avatar
R/C Tech Elite Subscriber
 
Join Date: Feb 2003
Posts: 1,847
Trader Rating: 2 (100%+)
Default

Quote:
Originally Posted by Kazador
Hi.I have JLR .12 Red Dot Engine. What type of glow plug is best for 16% nitro. I have PT6H Picco Plug, is it good for me?Thanks
That is a fine plug.
__________________
www.murnanmodified.com
Grinder is offline   Reply With Quote
Old 03-29-2007, 06:22 AM   #1267
Tech Master
 
Grinder's Avatar
R/C Tech Elite Subscriber
 
Join Date: Feb 2003
Posts: 1,847
Trader Rating: 2 (100%+)
Default

Quote:
Originally Posted by serpentpro28
Thanks Uriah i will try that' btw what is the good temperature after the brake-in?
Thanks to you 2 dj' for the info'
I like for my glowplug temp to be under 300F on the +35. I usually run mine at or around 250-270F. I am using .8mm of total shims inside the engine. I am usiing Rocket Science 30%. C7TF plug. All of this can vary greatly with atmospheric conditions. Most important is to make sure your glowplug is not dry after you run. Temp guns vary widely on the temps that they give. Up to 50 degrees, or more sometimes. If my car is fast, and not slowing down, I run it. I do not care about engine temps. Sometimes they can be high even though you have plenty of lubrication. Especially on the Nova + engines. They create so much friction due to the tightness of the PS fit. Just look for some smoke coming out the exhaust
__________________
www.murnanmodified.com
Grinder is offline   Reply With Quote
Old 03-29-2007, 10:10 AM   #1268
Tech Master
 
Grinder's Avatar
R/C Tech Elite Subscriber
 
Join Date: Feb 2003
Posts: 1,847
Trader Rating: 2 (100%+)
Default

Attention all team drivers. Please email me pictures for the new team page.

Thanks, Uriah
__________________
www.murnanmodified.com
Grinder is offline   Reply With Quote
Old 03-29-2007, 10:27 AM   #1269
Tech Apprentice
 
AddictedToRacin's Avatar
 
Join Date: Mar 2007
Location: Freiberg, Germany
Posts: 76
Default

Just send me an engine and you'll get a pic
AddictedToRacin is offline   Reply With Quote
Old 03-29-2007, 03:36 PM   #1270
Tech Master
 
Grinder's Avatar
R/C Tech Elite Subscriber
 
Join Date: Feb 2003
Posts: 1,847
Trader Rating: 2 (100%+)
Default

Ninja .12 Powerpacks are back in stock.
__________________
www.murnanmodified.com
Grinder is offline   Reply With Quote
Old 03-29-2007, 09:36 PM   #1271
Tech Regular
 
colonrc's Avatar
 
Join Date: May 2006
Location: Rome,GA
Posts: 434
Default

Quote:
Originally Posted by Grinder
Attention all team drivers. Please email me pictures for the new team page.

Thanks, Uriah
You still got the E-mail the I send w/picture?
__________________
Serpent U.S.A , Maxy's Pro Racing Fuel , Murnan Modified Motors,Nexus Racing,Mike Desing,Member of GO-R/C
colonrc is offline   Reply With Quote
Old 03-30-2007, 09:24 AM   #1272
Tech Adept
 
sneezer714's Avatar
 
Join Date: Jan 2002
Location: Puerto Rico
Posts: 185
Trader Rating: 1 (100%+)
Default

Quote:
Originally Posted by colonrc
You still got the E-mail the I send w/picture?
Hey Eddie!
Saludos!
May be Murnan can use this one.

Murnan you can use this one for Junito Yukiyu:

and this one for Geovannie Gonzales:
__________________
JAVIER PAINT WORK'S
TEAM CFX PAINT WORK'S
sneezer714 is offline   Reply With Quote
Old 03-30-2007, 09:31 AM   #1273
Tech Adept
 
sneezer714's Avatar
 
Join Date: Jan 2002
Location: Puerto Rico
Posts: 185
Trader Rating: 1 (100%+)
Default

Im not a Team Driver but you can use this one



It's a joke, by the way I have a Murnan Mod. Engine Ready for the Latin American Cup !!!! I can't wait,
See you guy's in July
__________________
JAVIER PAINT WORK'S
TEAM CFX PAINT WORK'S
sneezer714 is offline   Reply With Quote
Old 03-30-2007, 10:00 AM   #1274
Tech Initiate
 
Join Date: May 2004
Location: Vega Baja, Puerto Rico
Posts: 26
Thumbs up

Gracias Javier...
__________________
Geovannie Gonzalez
Puerto Rico
Serpent America
Geovannie is offline   Reply With Quote
Old 03-30-2007, 10:17 AM   #1275
Tech Elite
 
dj apolaro's Avatar
 
Join Date: May 2005
Location: Miami, Fl.
Posts: 2,364
Default

Quote:
Originally Posted by Geovannie
Gracias Javier...

Is is july yet!!!!!!!!!!!
dj apolaro is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
MURNAN MODIFIED PLUS 21-7BT tmperformance1 R/C Items: For Sale/Trade 4 02-11-2008 01:00 PM
MRX-4R,murnan modified 35+21 ltrdude R/C Items: For Sale/Trade 19 12-11-2007 03:29 AM
Ninja TA01 Murnan Modified,OS TZ Modified GMartinez R/C Items: For Sale/Trade 31 08-20-2007 09:40 PM
Murnan Modified horizon644 Nitro On-Road 1 02-06-2007 09:32 PM
Murnan Modified Motors AlanLim Onroad Nitro Engine Zone 1 04-20-2004 12:01 AM



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 11:46 AM.


Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net

SEO by vBSEO 3.5.0