Serpent 705
#1021
i juz inspected my shocks, & found tat 1 of the rear shocks got problem, the e-ring came off (duno why?). i've re-do the shocks & hope tat it could reduce the problem. thx for the advice.
but another problem came up (lol)
i broke my 1.5mm allen wrench & the bit stay in the set screw. the set screw is used on the x-bracket to secure the roll-over bar, got any ideas to take out tat screw? i was tinking of drilling it but it's rather small, not sure if it works...
but another problem came up (lol)
i broke my 1.5mm allen wrench & the bit stay in the set screw. the set screw is used on the x-bracket to secure the roll-over bar, got any ideas to take out tat screw? i was tinking of drilling it but it's rather small, not sure if it works...
#1022
Tech Adept
I settled for this: 705, tp05 and NovaMega SX12 RE 3P Race Turbo MS
#1023
Tech Regular
Originally posted by taz5176
i juz inspected my shocks, & found tat 1 of the rear shocks got problem, the e-ring came off (duno why?). i've re-do the shocks & hope tat it could reduce the problem. thx for the advice.
but another problem came up (lol)
i broke my 1.5mm allen wrench & the bit stay in the set screw. the set screw is used on the x-bracket to secure the roll-over bar, got any ideas to take out tat screw? i was tinking of drilling it but it's rather small, not sure if it works...
i juz inspected my shocks, & found tat 1 of the rear shocks got problem, the e-ring came off (duno why?). i've re-do the shocks & hope tat it could reduce the problem. thx for the advice.
but another problem came up (lol)
i broke my 1.5mm allen wrench & the bit stay in the set screw. the set screw is used on the x-bracket to secure the roll-over bar, got any ideas to take out tat screw? i was tinking of drilling it but it's rather small, not sure if it works...
On that bit that stay in the x-bracket. It did happen to me before on my helicopter kit. What i did was to drill with the same size of drill bit and re-tread it with the next size of screw or setscrew. I had a hard time drilling with smaller drill bit since my wrench bit left inside was from a harden steel, but you can try on yours with smaller drill bit, if you don't want to lose the original tread. Good luck, u need it.
#1024
Tech Regular
Originally posted by JBrake
I think most will steer you toward the Ofna. I have used both and would say the Ofna is better in every area. I personally have an Integy truer and for the price I don't think it can be beat. My 2 cents
I think most will steer you toward the Ofna. I have used both and would say the Ofna is better in every area. I personally have an Integy truer and for the price I don't think it can be beat. My 2 cents
#1025
Tech Regular
Originally posted by johan
I settled for this: 705, tp05 and NovaMega SX12 RE 3P Race Turbo MS
I settled for this: 705, tp05 and NovaMega SX12 RE 3P Race Turbo MS
Just a note, don't you want to race legal in ROAR or some national?
#1026
Tech Adept
iTrader: (1)
InitialD -
What do you mean by reversed? Do you have a picture of this?
With Sanwa / Airtronics, I believe you can install the steering servos as per the instruction in the 705 manual. Those of us with other servos have to install the steering servo linkages reversed...
#1027
Tech Regular
Originally posted by rc-racer
InitialD -
What do you mean by reversed? Do you have a picture of this?
InitialD -
What do you mean by reversed? Do you have a picture of this?
#1028
go to 3 deg rear toe.
#1029
Tech Adept
Good!!! Go get it!!!
Just a note, don't you want to race legal in ROAR or some national?
Just a note, don't you want to race legal in ROAR or some national?
Im more concerned with EFRA rules, and from what im Ive been told this engine should be legal. At club-level its allowed for sure. In any case my focus will be on getting this baby up and running first, so Im not so worried about it.
Last edited by johan; 04-07-2003 at 04:25 PM.
#1031
Tech Adept
iTrader: (1)
Hey guys, I have the Novarossi RS-12 S3 and need a race legal header/pipe.
Can you tell me if these will be race legal and work with my engine?
Header
Pipe
Or will this set work and be race legal?
Complete set
Thanks
Can you tell me if these will be race legal and work with my engine?
Header
Pipe
Or will this set work and be race legal?
Complete set
Thanks
#1032
Originally posted by johan
I settled for this: 705, tp05 and NovaMega SX12 RE 3P Race Turbo MS
I settled for this: 705, tp05 and NovaMega SX12 RE 3P Race Turbo MS
#1033
Originally posted by taz5176
but another problem came up (lol)
i broke my 1.5mm allen wrench & the bit stay in the set screw. the set screw is used on the x-bracket to secure the roll-over bar, got any ideas to take out tat screw? i was tinking of drilling it but it's rather small, not sure if it works...
but another problem came up (lol)
i broke my 1.5mm allen wrench & the bit stay in the set screw. the set screw is used on the x-bracket to secure the roll-over bar, got any ideas to take out tat screw? i was tinking of drilling it but it's rather small, not sure if it works...
#1034
Originally posted by rc-racer
InitialD -
What do you mean by reversed? Do you have a picture of this?
InitialD -
What do you mean by reversed? Do you have a picture of this?
#1035
Originally posted by rc-racer
Hey guys, I have the Novarossi RS-12 S3 and need a race legal header/pipe.
Can you tell me if these will be race legal and work with my engine?
Header
Pipe
Or will this set work and be race legal?
Complete set
Thanks
Hey guys, I have the Novarossi RS-12 S3 and need a race legal header/pipe.
Can you tell me if these will be race legal and work with my engine?
Header
Pipe
Or will this set work and be race legal?
Complete set
Thanks
The one with the separate pipe will not fit correctly with the separate polished header that you showed. The pipe alone is actually the same pipe as the one in the complete inline pipe set (51640).