Serpent 960....
#1786
The dogbone is the driveshaft.
The A Arms are the plastic parts that connect the upper wishbone to the bodymount.
When mounting the rear anti roll bar, first put the 2 blades into their aluminium mount (the part that pivots on the bearings). Then you can either pop the anti roll bar track rods onto the blades or attach them to the blades first and then mount them to the lower wishbone.
I see from the picture that you have the anti roll bar track rods mounted on the new outer most hole. This could be the reason it doesnt mount? See if you can mount it first to one of the two inner mounting holes first.
Also just to make sure that you know that the anti roll bar connects through the opening in the top wishbone?
The A Arms are the plastic parts that connect the upper wishbone to the bodymount.
When mounting the rear anti roll bar, first put the 2 blades into their aluminium mount (the part that pivots on the bearings). Then you can either pop the anti roll bar track rods onto the blades or attach them to the blades first and then mount them to the lower wishbone.
I see from the picture that you have the anti roll bar track rods mounted on the new outer most hole. This could be the reason it doesnt mount? See if you can mount it first to one of the two inner mounting holes first.
Also just to make sure that you know that the anti roll bar connects through the opening in the top wishbone?
#1787
Tech Regular
i think ive solved it i disconnected the "pin" that is connected to blade and the other mountpoint on the other place...
it was very easy..
but i got some shims/orings left.. and some screws.
dont know what to do with them hehe
maybe something will throw of the car when i am driving or something...
hmm.. my rearbelt is very slack.. i have the belt tensionsetting as "default"
maybe i should tried "tightest"
but i dont know a solution for easy change that belt tension without taking the whole car apart
it was very easy..
but i got some shims/orings left.. and some screws.
dont know what to do with them hehe
maybe something will throw of the car when i am driving or something...
hmm.. my rearbelt is very slack.. i have the belt tensionsetting as "default"
maybe i should tried "tightest"
but i dont know a solution for easy change that belt tension without taking the whole car apart
#1789
Tech Regular
my friend helped me yesterday with some things..
doing some mods today for the 960.. example grind on the carbon body support-plate so its not contact the rear belt in lowest position.
changing some screws and so..
i need to take the car down again!!!
gonna change all wheel bearings to ceramic.. 12x18x4
and maybe buy the titanium pivot balls
My 960 today
http://umea3.mine.nu/gallery2/main.php?g2_itemId=420
doing some mods today for the 960.. example grind on the carbon body support-plate so its not contact the rear belt in lowest position.
changing some screws and so..
i need to take the car down again!!!
gonna change all wheel bearings to ceramic.. 12x18x4
and maybe buy the titanium pivot balls
My 960 today
http://umea3.mine.nu/gallery2/main.php?g2_itemId=420
Last edited by Orfeous; 11-05-2006 at 07:46 AM.
#1790
...hmm..
Hi guys, first try in 1/8 class here
anybody has an easy method to "reset" the MAIN needle of an ZX21 DS2 to "factory settings" (if there is such thing) ?
Although i had "marked" the original position, i mess up counting when trying to "bench run" her.
what can i say i did a silly mistake and i dont expect to be the last...
Hi guys, first try in 1/8 class here
anybody has an easy method to "reset" the MAIN needle of an ZX21 DS2 to "factory settings" (if there is such thing) ?
Although i had "marked" the original position, i mess up counting when trying to "bench run" her.
what can i say i did a silly mistake and i dont expect to be the last...
#1791
Tech Apprentice
960 car and parts
does anyone have info on shops in the us or web sights for serpent dealers,
for best prices and service thanks
for best prices and service thanks
#1792
Tech Elite
Thread Starter
Originally Posted by emankov
...hmm..
Hi guys, first try in 1/8 class here
anybody has an easy method to "reset" the MAIN needle of an ZX21 DS2 to "factory settings" (if there is such thing) ?
Although i had "marked" the original position, i mess up counting when trying to "bench run" her.
what can i say i did a silly mistake and i dont expect to be the last...
Hi guys, first try in 1/8 class here
anybody has an easy method to "reset" the MAIN needle of an ZX21 DS2 to "factory settings" (if there is such thing) ?
Although i had "marked" the original position, i mess up counting when trying to "bench run" her.
what can i say i did a silly mistake and i dont expect to be the last...
This is a rich setting.....
http://www.rctech.net/forum/showpost...&postcount=992
#1793
Originally Posted by brad151
does anyone have info on shops in the us or web sights for serpent dealers,
for best prices and service thanks
for best prices and service thanks
brad you can try Kamikaze Toys and Hobbies. They have the full line of 960 parts and optionals. They always have everything in stock and provide fast and friendly customer service.
give them a call at 714-997-8697. Theyre located in So. Cal, but they ship to where ever its needed. or you can shoot an Email to [email protected]
#1795
How's the 960 doing
Originally Posted by C Verano
Yup still kicking just taking care of things at work. I'll PM my current set-up for the CR to you. How's the 960 doing for you?
Edit: Madbeats...Setup is in your PM.
Edit: Madbeats...Setup is in your PM.
#1796
madbeats nice line up even the buggy thinking about having some fun in the dirt too
#1797
Captian whut up !!!!!!!!!!!
Originally Posted by captian
madbeats nice line up even the buggy thinking about having some fun in the dirt too
#1798
Originally Posted by madbeats
Chris Da super bad fully hop uped is sitting down .. till the new season starts here's are a pic of my team for next year.. still working out and testing some setting.... but all good.
#1799
Tech Regular
My 960 under development
#1800
Tech Master
For all U guys that reported clutches blowing up at the Vegas race..take a look at this!! http://www.mytsn.com/products/desc.asp?prid=4365