Mugen MTX-3
Why is Mugen putting out a warmed over MTX-3???
Are they trying to be like Serpent with the Impulse and 705!?!?
Are they trying to be like Serpent with the Impulse and 705!?!?
Re: Re: Re: About belts
Originally posted by tonimccloud
thanks for your replies manticore . I know that kFactory's belts fits in V one, but does it fit on my mugen?? you know the size of mugen front, rear and side belts??
thanks for your replies manticore . I know that kFactory's belts fits in V one, but does it fit on my mugen?? you know the size of mugen front, rear and side belts??
Traction Rolling
Hey people...
On the last major race I did, I had some problems with traction rolling. Even after widening the front end, hardening springs, tyres and bars, lowering the car, everything I have always been doing, with sucess, but this time I got no success. My car would still roll.
Any suggestions?
Patrick Bandeira de Mello
- Bandeira Racing Team -
On the last major race I did, I had some problems with traction rolling. Even after widening the front end, hardening springs, tyres and bars, lowering the car, everything I have always been doing, with sucess, but this time I got no success. My car would still roll.
Any suggestions?
Patrick Bandeira de Mello
- Bandeira Racing Team -
Last edited by Bandeira; 04-04-2004 at 06:17 PM.
About belts, most belts are available from industrial belt suppliers. You just need to know the pitch and No. of teeth, they will usually cut them to width if you buy enough.
Re: Traction Rolling
Originally posted by Bandeira
Hey people...
On the last major race I did, I had some problems with traction rolling. Even after widening the front end, hardening springs, tyres and bars, lowering the car, everything I always have been doing, with sucess, but this time I got no success. My car would still roll.
Any suggestions?
Patrick Bandeira de Mello
- Bandeira Racing Team -
Hey people...
On the last major race I did, I had some problems with traction rolling. Even after widening the front end, hardening springs, tyres and bars, lowering the car, everything I always have been doing, with sucess, but this time I got no success. My car would still roll.
Any suggestions?
Patrick Bandeira de Mello
- Bandeira Racing Team -
Yeah... The droop was 0, i think...
The tyres were about 60mm at the start of a 30min semi...
The changes I thought about were the same as you did...
After the event I thought on everything and it was a huge learning...
Next time I'd better harden my rear sway bar so I could be able to set a smaller amount for dual-rate...
Any other suggestions?
The tyres were about 60mm at the start of a 30min semi...
The changes I thought about were the same as you did...
After the event I thought on everything and it was a huge learning...
Next time I'd better harden my rear sway bar so I could be able to set a smaller amount for dual-rate...
Any other suggestions?
Last edited by Bandeira; 04-05-2004 at 09:17 AM.
At what part of the corner do you roll?
Tech Regular
motor
will the rb x12 on my nitro tc3 work on an mtx-3?
Re: Traction Rolling
Originally posted by Bandeira
Hey people...
On the last major race I did, I had some problems with traction rolling. Even after widening the front end, hardening springs, tyres and bars, lowering the car, everything I have always been doing, with sucess, but this time I got no success. My car would still roll.
Any suggestions?
Patrick Bandeira de Mello
- Bandeira Racing Team -
Hey people...
On the last major race I did, I had some problems with traction rolling. Even after widening the front end, hardening springs, tyres and bars, lowering the car, everything I have always been doing, with sucess, but this time I got no success. My car would still roll.
Any suggestions?
Patrick Bandeira de Mello
- Bandeira Racing Team -
I run pretty much the stock set-up and when the track is sprayed with a high traction compound (VHT). I just go to 42 or 45 shore tire all the way around on the car and it works fine. No traction rolling for me.
Tech Master
iTrader: (13)
Re: motor
Originally posted by jiggamacdaddy
will the rb x12 on my nitro tc3 work on an mtx-3?
will the rb x12 on my nitro tc3 work on an mtx-3?
Tech Elite
iTrader: (4)
Join Date: Sep 2001
Location: Louisville, KY!.. USA!! ....Home of http://www.fastharry.com
Posts: 2,847
Trader Rating: 4 (100%+)
Originally posted by FAST1
Why is Mugen putting out a warmed over MTX-3???
Are they trying to be like Serpent with the Impulse and 705!?!?
Why is Mugen putting out a warmed over MTX-3???
Are they trying to be like Serpent with the Impulse and 705!?!?
If they wanted to be like Serpent,they'd have to give back all their trophy's.....
Re: motor
Originally posted by jiggamacdaddy
will the rb x12 on my nitro tc3 work on an mtx-3?
will the rb x12 on my nitro tc3 work on an mtx-3?
Tech Regular
yeah it did i just ment crank shaft size and style, but i think i have question answerd now.
thanks anyways
thanks anyways
Originally posted by fastharry
If they wanted to be like Serpent,they'd have to give back all their trophy's.....
If they wanted to be like Serpent,they'd have to give back all their trophy's.....
Tech Master
iTrader: (13)
Originally posted by jiggamacdaddy
yeah it did i just ment crank shaft size and style, but i think i have question answerd now.
thanks anyways
yeah it did i just ment crank shaft size and style, but i think i have question answerd now.
thanks anyways