Mugen MTX-3
#5476
HI!
I am having problems with the MTX3 not rolling freely. The brakes seems to be binding!!
Any help is appreciated!
I am having problems with the MTX3 not rolling freely. The brakes seems to be binding!!
Any help is appreciated!
#5477
Originally posted by FAST1
HI!
I am having problems with the MTX3 not rolling freely. The brakes seems to be binding!!
Any help is appreciated!
HI!
I am having problems with the MTX3 not rolling freely. The brakes seems to be binding!!
Any help is appreciated!
Either pull the pads out and sand them down a fraction.
Or you can run a few tanks as it is and they should free up a bit.
Running tanks through the car is much more fun.
Al
#5478
Thanks!! I'll give it a try!
Also what tires fit on this car......the tires i have (Nitro Shoes) seems to hit the rear hubs!!
Also what tires fit on this car......the tires i have (Nitro Shoes) seems to hit the rear hubs!!
#5479
Originally posted by FAST1
HI!
I am having problems with the MTX3 not rolling freely. The brakes seems to be binding!!
Any help is appreciated!
HI!
I am having problems with the MTX3 not rolling freely. The brakes seems to be binding!!
Any help is appreciated!
Now, it'll roll very freely...
#5480
Originally posted by InitialD
Should be 363 mm in length which is equivalent to 121 teeths on the belt. 363 teeths would give you a very long belt.
Should be 363 mm in length which is equivalent to 121 teeths on the belt. 363 teeths would give you a very long belt.
darn it! even a flunkie like I am can figure that out... wow...
#5481
everyone n their mama's seem to have an mtx-3 now... its like an ntc3
#5482
And...............................
#5483
Originally posted by eddiethefish
Can I say the ratio of length/teeth is 3:1 then?
darn it! even a flunkie like I am can figure that out... wow...
Can I say the ratio of length/teeth is 3:1 then?
darn it! even a flunkie like I am can figure that out... wow...
#5484
Originally posted by cHckbOY5
everyone n their mama's seem to have an mtx-3 now... its like an ntc3
everyone n their mama's seem to have an mtx-3 now... its like an ntc3
#5485
Originally posted by Manticore
of cuz that simple math that a flunkie can figure it out !! you think you are too good at this?
of cuz that simple math that a flunkie can figure it out !! you think you are too good at this?
#5486
Originally posted by acs
Corse-R
The belts for the conversion are they 363 teeth or 363mm in length? Trying to find a source locally for them.
Thanks
Al
Corse-R
The belts for the conversion are they 363 teeth or 363mm in length? Trying to find a source locally for them.
Thanks
Al
#5487
Originally posted by FAST1
Thanks!! I'll give it a try!
Also what tires fit on this car......the tires i have (Nitro Shoes) seems to hit the rear hubs!!
Thanks!! I'll give it a try!
Also what tires fit on this car......the tires i have (Nitro Shoes) seems to hit the rear hubs!!
#5488
Originally posted by Corse-R
363mm of lenght. 121 Tooth in total if not remember bad, belt pitch is 3mm.
363mm of lenght. 121 Tooth in total if not remember bad, belt pitch is 3mm.
Mr. Manticore : bet you have problem with that too.
#5489
Originally posted by Corse-R
You need to use the 2º offset rear wheels.
You need to use the 2º offset rear wheels.
#5490
Tech Adept
iTrader: (1)
Alright guys, i got my MTX-3 today and started building it. Im glad to be a part of this forum now. Anyways, did anyone have trouble putting that clip next to the one way, that was so hard for me. I was just wondering if anyone else had trouble. Construction is going smooth and cant wait to be done!