Mugen MTX-4
#8701
I was curious about what happened, until I clicked on one of those " tech elite " avitars:
http://rctech.net/forum/payments.php
#8702
S3 O-rings in the shafts of the differential
Hello all,
Do you install the S3 o-rings behind the satelite gears of the differential?
I suppose that their purpose is the differential to lock more on power. Correct?
Do you install the S3 o-rings behind the satelite gears of the differential?
I suppose that their purpose is the differential to lock more on power. Correct?
#8703
#8704
hi,
does anyone come across this problem?my ride was mugen mtx-4
-2mm hex screw head strip until look like a circle~ (how to take that screw out???mine was silver steel screw at front steering ,upper deck)
-1.5mm front droops 1 side strip too...
pls help, i cant able to get that 1.5mm out at 1st ,then the 2nd matter 2mm screw problem comes again~very very frastrated ...
im new just involve rc half years , any pro advice will kindly appriciate, sorry for my bad english too...
ps:im not sure am i posting the correct thread here or rookies zone, i will post both hope is ok
does anyone come across this problem?my ride was mugen mtx-4
-2mm hex screw head strip until look like a circle~ (how to take that screw out???mine was silver steel screw at front steering ,upper deck)
-1.5mm front droops 1 side strip too...
pls help, i cant able to get that 1.5mm out at 1st ,then the 2nd matter 2mm screw problem comes again~very very frastrated ...
im new just involve rc half years , any pro advice will kindly appriciate, sorry for my bad english too...
ps:im not sure am i posting the correct thread here or rookies zone, i will post both hope is ok
Last edited by tancp81; 11-08-2007 at 02:06 AM.
#8705
For the servo saver take the top deck off but undoing the bottom scre and atering arms - you should be able to turn the shaft from underneath with a pair of pliers.
For the droop screws you may be able to get to the bottom of the screw with pliers and wind the srew all the way out.
Good luck
For the droop screws you may be able to get to the bottom of the screw with pliers and wind the srew all the way out.
Good luck
#8706
For the servo saver take the top deck off but undoing the bottom scre and atering arms - you should be able to turn the shaft from underneath with a pair of pliers.
For the droop screws you may be able to get to the bottom of the screw with pliers and wind the srew all the way out.
Good luck
For the droop screws you may be able to get to the bottom of the screw with pliers and wind the srew all the way out.
Good luck
#8707
hi,
does anyone come across this problem?my ride was mugen mtx-4
-2mm hex screw head strip until look like a circle~ (how to take that screw out???mine was silver steel screw at front steering ,upper deck)
-1.5mm front droops 1 side strip too...
pls help, i cant able to get that 1.5mm out at 1st ,then the 2nd matter 2mm screw problem comes again~very very frastrated ...
im new just involve rc half years , any pro advice will kindly appriciate, sorry for my bad english too...
ps:im not sure am i posting the correct thread here or rookies zone, i will post both hope is ok
does anyone come across this problem?my ride was mugen mtx-4
-2mm hex screw head strip until look like a circle~ (how to take that screw out???mine was silver steel screw at front steering ,upper deck)
-1.5mm front droops 1 side strip too...
pls help, i cant able to get that 1.5mm out at 1st ,then the 2nd matter 2mm screw problem comes again~very very frastrated ...
im new just involve rc half years , any pro advice will kindly appriciate, sorry for my bad english too...
ps:im not sure am i posting the correct thread here or rookies zone, i will post both hope is ok
Do you have a dremel thin disc ?
Dremel the screw to make a line, and then use a flat screwdriver ( preferably thin and wide point ).
#8708
no i dun have dremel ,here selling very expensive so refuse to buy 1 since i was just half year expenriance rc exciment~
at the end the screw was taken out by bigger plier by holding bottom of the steering stand , twist it n "click" , loose~
ps: never buy steel screw again... never~(i realize, those original black screw more tough than that~hmm)
#8709
Tech Initiate
what kind of rc battery does the mtx4 use? hump, or flat?
#8710
They use a flat pack
#8711
Does anybody have a MTX4 (preferably MTX4R) editable setup sheet that they could share with me? Links or please email: [email protected]
Thanks in advance!
Thanks in advance!
#8712
Ran my car for the first time here in Sydney at yesterday's Winter Champs, and i must say how impressed i am with the way the car handles on the track, didn't fare so good with some small gremlins creeping in, but on a whole this has some pertentual, just need my driving skills to improve 100 fold , next weekend is another race day to over come the problems i had
#8713
Tech Initiate
what kind of starter box do they use? please include links to them!
#8714
#8715
Does anybody have a MTX4 (preferably MTX4R) editable setup sheet that they could share with me? Links or please email: [email protected]
Thanks in advance!
Thanks in advance!
Someone reported it as broken link earlier (thanks) so I've fixed it and hosted the file directly.