Serpent Cobra GT
#2506
Tech Rookie
A question
The new Cluth Bell Its better than the stock one?
The new Cluth Bell Its better than the stock one?
#2507
Tech Regular
#2508
Tech Addict
Hello from France,
no problem with the screws. Just don't hesitate to screw strong!!!
no problem with the screws. Just don't hesitate to screw strong!!!
#2509
Linkages play
Hello Gents,
A question about linkages play. I know it's a much debated topic in RC in general but I tend to believe the linkages play, especially on the steering servo linkage to the servo saver post is huge. Also the steering rods and the camber linkages do have quite a bit of play. Do I just need to replace them or are there better aftermarket linkages I can use. Did a lot of searching already but thought I'd ask here for some good advice....
thx in advance
w.
A question about linkages play. I know it's a much debated topic in RC in general but I tend to believe the linkages play, especially on the steering servo linkage to the servo saver post is huge. Also the steering rods and the camber linkages do have quite a bit of play. Do I just need to replace them or are there better aftermarket linkages I can use. Did a lot of searching already but thought I'd ask here for some good advice....
thx in advance
w.
#2510
Hello Gents,
A question about linkages play. I know it's a much debated topic in RC in general but I tend to believe the linkages play, especially on the steering servo linkage to the servo saver post is huge. Also the steering rods and the camber linkages do have quite a bit of play. Do I just need to replace them or are there better aftermarket linkages I can use. Did a lot of searching already but thought I'd ask here for some good advice....
thx in advance
w.
A question about linkages play. I know it's a much debated topic in RC in general but I tend to believe the linkages play, especially on the steering servo linkage to the servo saver post is huge. Also the steering rods and the camber linkages do have quite a bit of play. Do I just need to replace them or are there better aftermarket linkages I can use. Did a lot of searching already but thought I'd ask here for some good advice....
thx in advance
w.
Another thing which is overlooked is the actual play in the steering servo itself. I used to run SAVOX but found the gears very soon developed a lot of play in them which actually made the rest of the steering system seem to have lots of play. I now run SANWA SRG-BX servos in GT (I was already using them in Buggy and 1/8 circuit) and most of the play went away as the servo them had no neutral play whatsoever.
#2511
I think the steering rod linkages and the servo linkage are the same as the 3.0. The standard RTR ackerman bar sucks as Serpent puts 3 mm threaded bolts into the metal 3.5 mm bushings instead of using the kingpins. I replaced it by the ball bearing one. The savox 2290 has 1 hour of work under the belt as I burnt up 2 savox 1268's already. It's not the servo, it's not the ackerman. It's only the steering rods and the servo link. I was just wandering whether this is normal after let say about 10 liters of fuel. Replacing is easy but maybe there something better?...
w.
w.
#2512
I think the steering rod linkages and the servo linkage are the same as the 3.0. The standard RTR ackerman bar sucks as Serpent puts 3 mm threaded bolts into the metal 3.5 mm bushings instead of using the kingpins. I replaced it by the ball bearing one. The savox 2290 has 1 hour of work under the belt as I burnt up 2 savox 1268's already. It's not the servo, it's not the ackerman. It's only the steering rods and the servo link. I was just wandering whether this is normal after let say about 10 liters of fuel. Replacing is easy but maybe there something better?...
w.
w.
#2514
Chassis on a flat plate and with the wheel hex on a parallel with the flat plate measure the droop from the bottom of the hex to the board. In general I start with 25mm in the front and 26mm in the rear. I run the car very stiff with very little uplift on the GT.
#2515
Tech Master
iTrader: (42)
If anyone is looking for a Cobra GT, I have a brand new ready to run with motor, servos, pipe/header, 811 GT suspension upgrade, gears, springs, sweep tires. Everything is brand new. No time to play, to many hobbies.
http://www.rctech.net/forum/r-c-item...-0-roller.html
http://www.rctech.net/forum/r-c-item...-0-roller.html
#2517
Tech Master
Anyone know when new kits might be in stock?
#2518
#2519
Tech Initiate
I heard there won't be 3.1 kits.