Kyosho v-one rrr
#8042
Tech Adept
Originally Posted by boner
Yes, it's able to support your RX and servo but the question is how is it going to fit on your RRR (assuming that is the car the battery is going on).
#8043
Originally Posted by markp27
What tyres are you using? Make sure you're using at least a 2mm split front-to-rear.
If you're car is suffering from turn-in understeer either change the spool to a diff with 30,000 or 50,000 oil or even a one-way, as long as you don't have to brake too much.
Set the rear anti-roll bar harder or go to the harder version.
How do you have your front anti-roll bar set?
If you're car is suffering from turn-in understeer either change the spool to a diff with 30,000 or 50,000 oil or even a one-way, as long as you don't have to brake too much.
Set the rear anti-roll bar harder or go to the harder version.
How do you have your front anti-roll bar set?
front roll bar fully horizontal
that's why i go for spool..
#8044
Why my pinion gear wear faster? i think i set gear mesh correctly..
may i use steel pinion gear? unfortunelly my LHS out of stock the steel ones.
Can i use Mugen MTX4 1st and 2nd pinion gear? is that work with V1RRR standart clutch bell? Thanks
may i use steel pinion gear? unfortunelly my LHS out of stock the steel ones.
Can i use Mugen MTX4 1st and 2nd pinion gear? is that work with V1RRR standart clutch bell? Thanks
#8045
re-motor
Cheers mate. On the Novarossi...How does it compare to the TZ then? Im looking at getting it fairly cheap..Maybe to have as a second motor or backup motor. However... if its not as good as the TZ, i wont worry about getting it..
#8046
Tech Apprentice
Originally Posted by rmdhawaii
#8047
Originally Posted by rayjay
I have a question...I currently have a rrr with a .12 OS TZ. Our track is tight and twisty and i was looking at getting a motor with a bit more punch in it. Im looking at getting an Novarossi Rex RER12. Any thoughts if this will be much of an improvement. Also... what motor do you guys recomend.
I have also used the Tz in the past with great results......but the motor I would recommend if you want awesome grunt and so far has been a workhorse is the new Evo3 STI made by Sirio...just loook at what it did at the worlds.... This motor has taken very good care of me at very big races and i have no complaints... Hope this helps
#8048
Originally Posted by robert maestrey
I have also used the Tz in the past with great results......but the motor I would recommend if you want awesome grunt and so far has been a workhorse is the new Evo3 STI made by Sirio...just loook at what it did at the worlds.... This motor has taken very good care of me at very big races and i have no complaints... Hope this helps
#8049
Originally Posted by spyspeed
Why my pinion gear wear faster? i think i set gear mesh correctly..
may i use steel pinion gear? unfortunelly my LHS out of stock the steel ones.
Can i use Mugen MTX4 1st and 2nd pinion gear? is that work with V1RRR standart clutch bell? Thanks
may i use steel pinion gear? unfortunelly my LHS out of stock the steel ones.
Can i use Mugen MTX4 1st and 2nd pinion gear? is that work with V1RRR standart clutch bell? Thanks
#8050
Originally Posted by litespeed-dom
You already have one of the torque'st .12 motor out there. Stick with your TZ.
Dom
Dom
#8051
re- motor
Thanks......
#8052
Tech Elite
iTrader: (4)
Originally Posted by wallyedmonds
if you think it has torque than theres somthing wrong with your other motors.
Dom
#8053
Tech Champion
iTrader: (91)
Originally Posted by wallyedmonds
but novarossis wont break like a sirio and many have broken the sti
Be more specific & give more details than just bashing the sirio motor.
I guess all the motors that made it to the top ten in the worlds were just an average motor with no torque
#8054
Originally Posted by spyspeed
40Shore up front and 37 rear.. and 2mm split front-to-rear..
front roll bar fully horizontal
that's why i go for spool..
front roll bar fully horizontal
that's why i go for spool..
What do you mean about the spool?
#8055
Originally Posted by litespeed-dom
You already have one of the torque'st .12 motor out there. Stick with your TZ.
Dom
Dom
Cheers, Mark.