RCAmerica/Xray,Hudy
#211
Yes on the hub I used a flat head screw with a countersunk washer, on the inside I used a button head screw ran it threw the link then put a washer and a lock nut. It worked really well.
Thanks Drew
#212
Tech Elite
iTrader: (30)
hey Drew,
I was just rebuilding my XXL3 and the new oring for the backplate seems like the new oring is way to big, Diameter seems correct but the thickness seems to big. I checked the part number against the Max pdf and its the right part number if they only had one pdf for the XXL3 and didn't revise it throughout the production. Have you seen the same thing?
I was just rebuilding my XXL3 and the new oring for the backplate seems like the new oring is way to big, Diameter seems correct but the thickness seems to big. I checked the part number against the Max pdf and its the right part number if they only had one pdf for the XXL3 and didn't revise it throughout the production. Have you seen the same thing?
#213
hey Drew,
I was just rebuilding my XXL3 and the new oring for the backplate seems like the new oring is way to big, Diameter seems correct but the thickness seems to big. I checked the part number against the Max pdf and its the right part number if they only had one pdf for the XXL3 and didn't revise it throughout the production. Have you seen the same thing?
I was just rebuilding my XXL3 and the new oring for the backplate seems like the new oring is way to big, Diameter seems correct but the thickness seems to big. I checked the part number against the Max pdf and its the right part number if they only had one pdf for the XXL3 and didn't revise it throughout the production. Have you seen the same thing?
Thanks Drew
#215
SRC Bodies are in stock
Guys just wanted you to know that the SRC order of bodies showed up and are in stock. I will post the new price on them tomorrow.
Thanks Drew
Thanks Drew
#217
#219
Drivetrain Calculator
Does anybody know where I can find a drivetrain ratio calculator that allows me to input all of the pulleys?
I remember seeing one somebody created in excel, but I cannot seem to find it again.
I remember seeing one somebody created in excel, but I cannot seem to find it again.
#220
Tech Elite
iTrader: (34)
So I sent it to: [email protected]
It may not be the one you previously found... But it should do the trick...
The current pulleys are from the Xray NT1.
#221
I couldn't upload it here...
So I sent it to: [email protected]
It may not be the one you previously found... But it should do the trick...
The current pulleys are from the Xray NT1.
So I sent it to: [email protected]
It may not be the one you previously found... But it should do the trick...
The current pulleys are from the Xray NT1.
I will check it out later.
#222
Xray sweaps Kraceway 2010 U.S. Open
Congrats to the winners:
1. Paul Lemieux (TQ) Xray NT1
2. Uriah Murnan Xray NT1
3. Eric Jones Xray NT1
Great job guys.
Thanks Drew
1. Paul Lemieux (TQ) Xray NT1
2. Uriah Murnan Xray NT1
3. Eric Jones Xray NT1
Great job guys.
Thanks Drew
#223
Tech Champion
iTrader: (91)
Track record fastest lap
7 out of 11 cars were Xray that ran in the AAA Mains
Previous track lap record was 16.5
Paul was on a mission & set the new fastest lap record @ 16.3
TedX was pressing the annoucing to paul to give us a 16.1 in the A3 paul was giving it his all maybe next time
Congrats to Paul n the entire Xray Team
Previous track lap record was 16.5
Paul was on a mission & set the new fastest lap record @ 16.3
TedX was pressing the annoucing to paul to give us a 16.1 in the A3 paul was giving it his all maybe next time
Congrats to Paul n the entire Xray Team
#224
Thanks again
Just wanted to Thank Rcamerica,Hudy & the entire Xray Team in sending Paul & supporting our event with some really nice prizes
A lot of drivers walked away very happy
Thanks again & look forward to working together in 2011
A lot of drivers walked away very happy
Thanks again & look forward to working together in 2011
#225
Tech Master
iTrader: (26)
Join Date: Dec 2005
Location: (Holiday, Fl.) (CST.Allentown, Pa.)
Posts: 1,314
Trader Rating: 26 (100%+)
Its not a new link, its just some different hardware ralph had on his rear end camber links that was different than what I got.
top right pic
http://events.redrc.net/event-galler...ds/?nggpage=2#
top right pic
http://events.redrc.net/event-galler...ds/?nggpage=2#