Serpent 733 1/10 200mm touring
#3736
Tech Adept
#3738
I have 2 733.
One with front diff and one with front solid axle.
Yesterday both threw the front belt. Is that just bad luck or are they stretched or what?
What can I do to prevent this?
One with front diff and one with front solid axle.
Yesterday both threw the front belt. Is that just bad luck or are they stretched or what?
What can I do to prevent this?
#3739
Tech Elite
iTrader: (89)
Pass you soon...
#3740
Do you have the clip and side of the pulley on its place?
Usually the 2nd position from the front works. If you have spool and orange belt you might want to use the 2 tighter position. What are your front tires doing while braking? Do they stop? If so, decrease your brake EPA also.
Usually the 2nd position from the front works. If you have spool and orange belt you might want to use the 2 tighter position. What are your front tires doing while braking? Do they stop? If so, decrease your brake EPA also.
#3741
Yes, the pulley and the clip are on its place.
I have the orange belt.
I have the orange belt.
#3742
xceed clutch
just wondering if someone can tell me if the xceed clutch is:
1. any good.
2. uses the same serpent shoes since the xceed is only 30mm.
3. can anyone tell me when the new 2sp is going to become available to everyone?
1. any good.
2. uses the same serpent shoes since the xceed is only 30mm.
3. can anyone tell me when the new 2sp is going to become available to everyone?
#3743
Hello Andy,
1; you can upgrade your current Serpent clutch with the Xceed spring and nut (the Xceed spring is too tight on the Serpent nut). If you want to adjust the clutch from the outside easier you can also use the Xceed SPT bell.
2; I think you can use both
3; End of this month.
1; you can upgrade your current Serpent clutch with the Xceed spring and nut (the Xceed spring is too tight on the Serpent nut). If you want to adjust the clutch from the outside easier you can also use the Xceed SPT bell.
2; I think you can use both
3; End of this month.
#3744
Hello Andy,
1; you can upgrade your current Serpent clutch with the Xceed spring and nut (the Xceed spring is too tight on the Serpent nut). If you want to adjust the clutch from the outside easier you can also use the Xceed SPT bell.
2; I think you can use both
3; End of this month.
1; you can upgrade your current Serpent clutch with the Xceed spring and nut (the Xceed spring is too tight on the Serpent nut). If you want to adjust the clutch from the outside easier you can also use the Xceed SPT bell.
2; I think you can use both
3; End of this month.
#3746
Tech Elite
iTrader: (89)
Hello Andy,
1; you can upgrade your current Serpent clutch with the Xceed spring and nut (the Xceed spring is too tight on the Serpent nut). If you want to adjust the clutch from the outside easier you can also use the Xceed SPT bell.
2; I think you can use both
3; End of this month.
1; you can upgrade your current Serpent clutch with the Xceed spring and nut (the Xceed spring is too tight on the Serpent nut). If you want to adjust the clutch from the outside easier you can also use the Xceed SPT bell.
2; I think you can use both
3; End of this month.
Pass you soon...
#3748
new 733 parts
I have it on good authority that the new gearbox is similar to the 1/8th and comes with the side bracket as well.
#3749
plug
I have a Rossi R12 pixy motor which is the best plugs for this motor
#3750