Serpent 733 1/10 200mm touring

Reply Subscribe

Thread Tools

Search this Thread

10-16-2012, 04:54 AM

#4201

Pattojnr

Tech Elite

iTrader: (19)

Join Date: Apr 2006

Location: Perth Australia

Posts: 4,594

Trader Rating: 19 (100%+)

Quote:

Originally Posted by M.Abramowicz

ok. I'm not perfect.

:-)

When my right tires go off (left side F/37, R/40, right side F/40, R/42) then car was like this\ so spur always grab ground.

I start from 64rears 61.8 fronts.
Tires goes off that R side was 1-1.5mm smaller on diameter then L side.

Anyway, if I will stay with 733 just for fun, I will move up that gear shaft 1.5mm, just add hand made allu washers.

Regards!
m.

ps: velox ordered.

i have tried going harder shores on the side of the car that wears faster, and most times it doesnt really work out. a harder tyre can often produce more slippage, so infact it can wear even quicker than the lower shore tyre. what i have done instead, was start that tyre 1mm bigger but the same shore. if its for a longer race, then i tend to use a little bit of trim and in stops just go back a little at a time. 1mm isnt a huge difference to throw setup right out the window. infact the car just gets easier to drive as the diameter evens out, then you may just be 0.5 smaller rather than 1.5mm smaller. but you will have a more consistant car rather than a harder tyre.

11-22-2012, 12:35 AM

#4202

rc-goods

Tech Apprentice

Join Date: Jun 2011

Posts: 79

Trader Rating: 0

Zero Force Serpent 733 Bearing Kit Set

Zero Force Serpent 733 Bearing Kit Set (16pcs) (ZF-N12006)

Serpent 733 1/10 200mm touring-733_wm.jpg

www.rcgoods.com

02-16-2013, 03:43 PM

#4203

rbakker

Tech Regular

Join Date: Sep 2009

Location: Netherlands

Posts: 398

Trader Rating: 0

Hello guys,

the Serpent 733 has steel brake pads, can somebody tell me the distance between the 2 holes in the brake pad (center to center of hole)
Also the diameter of the holes in the brake pads.
(would be great if it is in mm...)

Want to try them in my car for the next race.

Kind regards,

Roy

03-08-2013, 02:35 PM

#4204

newera152

Tech Master

iTrader: (4)

Join Date: Jan 2005

Location: Conn

Posts: 1,031

Trader Rating: 4 (100%+)

Heres a Blitz custom painted body for the serpent 733, ready to mount.
http://www.ebay.com/itm/181094935013?

06-16-2013, 03:29 PM

#4205

swiftly

Tech Initiate

iTrader: (1)

Join Date: Dec 2010

Posts: 21

Trader Rating: 1 (100%+)

733 te dls question

Hi I have a 733 te and i have a problem with my dls . With no shocks on the car i can lift the right side of my suspension up and down freely and the left side knuckle moves the camber in and out like the dls should. But with my left side suspension when i move it up the right side arm and suspension starts to move up as well. I have the camber arms set to the outside hole of the knuckle in doing this do i need to change the lenght of the dls turn buckles too ,they are just set to the stock 45.5mm length.
I hope this makes sense trevor

06-17-2013, 07:37 PM

#4206

DayDAY

Tech Apprentice

Join Date: Jul 2009

Location: Hong Kong

Posts: 59

Trader Rating: 0

Hi all, just put on a new body with my Serpent 733...

Attached Thumbnails

Serpent 733 1/10 200mm touring-serpent-733-2.jpg

Serpent 733 1/10 200mm touring-seerpent-733-1.jpg

Serpent 733 1/10 200mm touring-serpent-733-3.jpg

Serpent 733 1/10 200mm touring-serpent-733-4.jpg

04-08-2018, 12:55 AM

#4207

DN419

Tech Initiate

iTrader: (3)

Join Date: Sep 2016

Posts: 20

Trader Rating: 3 (100%+)

Quote:

Originally Posted by RC MARKET

CSO 7075 T6 Hardcoated Pulley set

This may be a long shot, but can you still get these? Long discontinued I'm sure, but worth a shot. I'm big into Serpent 10th scale...any cool aluminum parts are of interest.

Thank you