Serpent 733 1/10 200mm touring
#3616
Tech Apprentice
iTrader: (10)
Hi Les,
Usually race at the Bayside club over at Wynnum......733 goes very well around there. (Be quiet RC Carnage! ) You should come on over and have a race sometime.
Will be venturing over to Brendale for the Qld champs again this year and maybe a race meet or two beforehand for a bit of testing.
Usually race at the Bayside club over at Wynnum......733 goes very well around there. (Be quiet RC Carnage! ) You should come on over and have a race sometime.
Will be venturing over to Brendale for the Qld champs again this year and maybe a race meet or two beforehand for a bit of testing.
#3617
Tech Elite
iTrader: (19)
Patto, thanks mate but i think you may have gotten the wrong impression! RC Carnage and i race against each other at our club and he's just putting s**t on me...... I have a setup i'm happy with.
I was just making the point that the Evo doesn't come with the correct camber plate for the DLS, (even though the DLS comes in the kit) only the standard one and it says to use the bottom set of holes when using the DLS. And yeah the pivot point is very different when comparing to my older 733 with DLS.......wondering why Serpent have done this??
I was just making the point that the Evo doesn't come with the correct camber plate for the DLS, (even though the DLS comes in the kit) only the standard one and it says to use the bottom set of holes when using the DLS. And yeah the pivot point is very different when comparing to my older 733 with DLS.......wondering why Serpent have done this??
#3618
Tech Apprentice
iTrader: (10)
i know Carnage was takin the piss, thats why i said car setup was an understatment. as it will effect the whole system, that you will have to resetup the rear for the pivot point change. basically it will change the leverage of the amount it will change the camber when activated. so it will be either a camber change, or it will be a rod length change. i made one for a Xray T3, so i played with all different points, and it changes it so much, you will be surprised. Cranage , bring on the Banter... umm what you drive ? piece of cheese ? an outdated Muggin ? or one of the new breed $$ cars
Just trying to figure out why Serpent have not included the camber plate specifically for the DLS, would have made it much easier.....
#3619
Tech Elite
iTrader: (19)
Thanks Patto, yeah just looking at it and think you are right, the pivot point with the new car is much higher so i'm thinking longer rods too, and re-adjust camber to suit.
Just trying to figure out why Serpent have not included the camber plate specifically for the DLS, would have made it much easier.....
Just trying to figure out why Serpent have not included the camber plate specifically for the DLS, would have made it much easier.....
#3621
Hi Les,
Usually race at the Bayside club over at Wynnum......733 goes very well around there. (Be quiet RC Carnage! ) You should come on over and have a race sometime.
Will be venturing over to Brendale for the Qld champs again this year and maybe a race meet or two beforehand for a bit of testing.
Usually race at the Bayside club over at Wynnum......733 goes very well around there. (Be quiet RC Carnage! ) You should come on over and have a race sometime.
Will be venturing over to Brendale for the Qld champs again this year and maybe a race meet or two beforehand for a bit of testing.
Cheers
#3622
Tech Apprentice
iTrader: (10)
Wynnum
#3626
[QUOTE=Team Chump;9078661]Hi Les,
Usually race at the Bayside club over at Wynnum......733 goes very well around there. (Be quiet RC Carnage! ) You should come on over and have a race sometime.
Will be venturing over to Brendale for the Qld champs again this year and maybe a race meet or two beforehand for a bit of testing.[/QUOTE
Usually race at the Bayside club over at Wynnum......733 goes very well around there. (Be quiet RC Carnage! ) You should come on over and have a race sometime.
Will be venturing over to Brendale for the Qld champs again this year and maybe a race meet or two beforehand for a bit of testing.[/QUOTE
Last edited by Les; 05-14-2011 at 03:35 AM.
#3627
can anyone tell me if there's a pinion tool for the 733, or is the one for the 966/960 fit the clutch bell of the 733
#3629
Tech Regular
Paolo Morganti takes the win in Ft Myers!