Bundy_Bear

iTrader: (11)

Enjoyed seeing Daniele car up close, it would be good to see Shepherd a little further up and wish them all the best today in the last two rounds of qualifying.

Andrew

kewdawg

iTrader: (3)

They're probably regretting not going there early like a lot of the other teams. They have a lot of work to do in a shorter amount of time. Hopefully, they can get it figured out in time.

G87z

iTrader: (7)

Correct Quinn. And they did not go for the pre-worlds. The setup their is much different than what ppl are normally using. Super soft.

kewdawg

iTrader: (3)

Not us. We know all about the soft stuff.

G87z

iTrader: (7)

Yea we do! LoL. The track was an electric style track. Just like the old BD!
It's all good. Every worlds event is a different mix of drivers in the final based on what part of the world is hosting the event.

kewdawg

iTrader: (3)

Yeah, G-Mac. I watched the recorded online feeds today. It was an amazing display of driving throughout the qualifiers and mains. I liked the layout. I noticed how that cross section toward the middle-right resembled our old track layout (in fact, the sweeper and the chicane leading to the straight is from our new track! Remember when Amador put that chicane in? ). Felt a little dejavu watching them drive it. Made me remember how It felt driving thru there. Their cars exhibited some of the same handling characteristics, too! Spooky, huh?! We might've done well there.

kewdawg

iTrader: (3)

U know, the more I think about it - that track is JUST like BD!!! The traction levels down to the crazy weather! We just don't have that really tall driver's stand.

boy2rc

Hello, I have some V10 spare part for sell and I accept offer http://www.rctech.net/forum/r-c-item...t-23-item.html

rc-goods

Zero Force Shepherd V10 Bearing kit set (16pcs) (ZF-N12009)



www.rcgoods.com

bigtee

Wondering whats going to be new for 2013 ? Does anyone have any opinions where improvement can be made? What does everyone think of the new chassis that shepherd has released,is it worth getting?

stefan

These would be my priorities and I think they are being considered:

- Front A-arms and steering hubs that eliminate the rubbing of the wheels on the lower shock eyelets.

- Two speed adaptor that secures the pin.
- The optional chassis brace in front of the engine should be a stock part because the car needs it.

crafty63

Has anyone tried the EC 2012 chassis update? With the ball bearing rear roll bar? Any comments on performance compared to the original v10?

joxes

Because of my new work I do not have time to practice and race. That’s why I’m selling an assembled Shepherd Velox V10 (2011/eleven) model. I bought the car through Shepherd USA.

This car has been assembled by myself and checked/tuned by my local hobby shop in Campbell CA.

The car was never raced. I used it 3 times (3 gas tanks). The engine is not even broken yet.

The following parts are installed on the car:

2 x Savox SC-1251MG Low Profile Digital "High Speed" Metal Gear Servo (SAV-SC-1251MG)
1 x Shepherd Li-Ion Receiver Battery Pack (7.4V/1800mAh) (SMR501800)
1 x Novarossi 353 Race.12/C 2009 3-Port .12 Competition On Road Engine (Turbo Plug)
1 x Spektrum SR300 receiver (3 channels)
1 x Novarossi Turbo #6 Short Body Ultra Glow Plug (Medium) (NOVC6TGF)
1 x Novarossi On Road Ins-Box Complete Set .12 30004
1 x Novarossi .12 On Road Conical Manifold Kit Medium 41616
1 x Novarossi EFRA 2652 Polished Tuned pipe for use with .12 competition engines. (NOV51614)
2 tires Xceed RC 26mm "Enneti" 1/10 Sedan Front Tires (37 Shore)
2 tires Xceed RC 30mm "Enneti" 1/10 Sedan Rear Tires (40 Shore) (XCD101509)


$700

Just PM me, I will share pictures

M.Abramowicz

iTrader: (1)

Jilles back!

http://www.redrc.net/2013/01/jilles-...herd-for-2013/

1evo RRR Driver

iTrader: (11)

You guys should b smiling and now maybe u will have something to talk about again in here, besides the cricket sounds!

Can't believe he went back!!