Serpent 710
06-03-2004, 10:33 AM
D, a friday pic for you!
Check out the sleave!!! Already polished and I've not even turned the engine over once 
06-03-2004, 10:33 AM
Re: Re: Re: Re: Re: 3 racing
Originally posted by markp27
This is what I found with the bumper brace, too. The two little alu posts which go into the foam bumper: I was putting the screws into them and tightening them up, when suddenly I felt the tension reduce as I was turning the screw - it had started to strip.
You're absolutely right about the alu being like chedder cheese
How's your engine coming along?
This is what I found with the bumper brace, too. The two little alu posts which go into the foam bumper: I was putting the screws into them and tightening them up, when suddenly I felt the tension reduce as I was turning the screw - it had started to strip.
You're absolutely right about the alu being like chedder cheese
How's your engine coming along?
The problem is you don't know if you have a bad part until you break it.
06-03-2004, 10:38 AM
Originally posted by Schrijver99
So come on Sunday and see a great race!
So come on Sunday and see a great race!
If I wake up Sunday.
06-03-2004, 10:55 AM
Re: D, a friday pic for you!
Originally posted by markp27
Check out the sleave!!! Already polished and I've not even turned the engine over once
Check out the sleave!!! Already polished and I've not even turned the engine over once
06-03-2004, 11:02 AM
Re: D, a friday pic for you!
Originally posted by markp27
Check out the sleave!!! Already polished and I've not even turned the engine over once
Check out the sleave!!! Already polished and I've not even turned the engine over once
06-03-2004, 11:09 AM
Re: Re: Re: Re: 3 racing
Originally posted by GlennCauley
I didn't even get a chance to run the darned thing.
I installed the carrying handle in the alu mounts, and then went to tighten the small grubscrews... twist... strip...
The alum. has the strength of lightweight cheddar cheese.
I didn't even get a chance to run the darned thing.
I installed the carrying handle in the alu mounts, and then went to tighten the small grubscrews... twist... strip...
The alum. has the strength of lightweight cheddar cheese.
06-03-2004, 11:11 AM
Re: Re: D, a friday pic for you!
Originally posted by Schrijver99
Looks just like mine! A shame that you don't come this weekend!
Looks just like mine! A shame that you don't come this weekend!
06-03-2004, 11:16 AM
Re: Re: Re: Re: Re: 3 racing
Originally posted by Sow&Steady
I rest my case
I rest my case
06-03-2004, 11:27 AM
Re: Re: Re: D, a friday pic for you!
Originally posted by markp27
Believe me, I would have prefered to come to, but not with a motor which isn't run in yet
Believe me, I would have prefered to come to, but not with a motor which isn't run in yet
06-03-2004, 11:33 AM
Re: Re: Re: Re: D, a friday pic for you!
Originally posted by Schrijver99
Is it with ceramic bearings?
Is it with ceramic bearings?
Actually the ceramic bearings look almost exactly like steel bearings Have a look at the pic attached.
06-03-2004, 12:38 PM
Re: Re: Re: Re: Re: D, a friday pic for you!
Originally posted by markp27
Yep! Actually the ceramic bearings look almost exactly like steel bearings Have a look at the pic attached.
Yep!
Actually the ceramic bearings look almost exactly like steel bearings Have a look at the pic attached.
$$$$ (btw mine is also with ceramic bearings
)
06-03-2004, 12:42 PM
Re: Re: Re: Re: Re: Re: D, a friday pic for you!
Originally posted by Schrijver99
$$$$
(btw mine is also with ceramic bearings )
$$$$ (btw mine is also with ceramic bearings
)
I'm hoping the weather is going to play ok tomorrow - I'll go to the track anyway and do the first few WOT tanks with the car off the track.
06-03-2004, 01:16 PM
Re: D, a friday pic for you!
Originally posted by markp27
Check out the sleave!!! Already polished and I've not even turned the engine over once
Check out the sleave!!! Already polished and I've not even turned the engine over once
props manI also heard that JP engines dont last very long maybe 2 gallons of fuel through them then they need to be rebuilt due to the fact that they are full bred racing engines
06-03-2004, 03:45 PM
I am the proud new owner of a baby s710 picked her up today I look forward to getting great advice from all you when ever I have a question about building it or some technical advice
06-03-2004, 04:05 PM
Originally posted by FW05R
I am the proud new owner of a baby s710 picked her up today I look forward to getting great advice from all you when ever I have a question about building it or some technical advice
I am the proud new owner of a baby s710 picked her up today I look forward to getting great advice from all you when ever I have a question about building it or some technical advice
Congrats on becoming a fellow snaker!!!!!!!!!!!!!! You will not be sorry for your purchase.It is an awesome ride.
WELCOME !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!
SNAKES RULE