Serpent 710
#5881
Originally posted by cyba888
So does that mean 66-62=4 divided by 2=2? Just making sure
So does that mean 66-62=4 divided by 2=2? Just making sure
#5882
Originally posted by cyba888
What I do is compress the car a bit and then measure it but sometimes its a bit off when I measure it repeatedly.
What I do is compress the car a bit and then measure it but sometimes its a bit off when I measure it repeatedly.
The shocks should settle nicely when you compress it a little or a lot to the bottom.
#5883
Re: Re: Re: One just for InitialD
Originally posted by InitialD
Yeah, but you will probably not miss the "coolest F1 race" in Bridgestone this year !
Yeah, but you will probably not miss the "coolest F1 race" in Bridgestone this year !
Eh, what is this I hear that you were down and around in KL the last week or so? Shopping for more spare parts?
Hey! Why aren't you at the Asean cup in Kuching???
What's the results?
#5884
Re: Re: Re: Re: One just for InitialD
Originally posted by Sow&Steady
Ahem .. you mean Silverstone.
Ahem .. you mean Silverstone.
Originally posted by Sow&Steady
Man ... can't sneak anything past you eh?
Man ... can't sneak anything past you eh?
Originally posted by Sow&Steady
Hey! Why aren't you at the Asean cup in Kuching???
Hey! Why aren't you at the Asean cup in Kuching???
Originally posted by Sow&Steady
What's the results?
What's the results?
#5886
I assembled my front knuckles tonight. On one of them, even with the wheel on and nut tightened, I can grab the wheel and move it back and forth about 0.3mm. This doesn't seem right because my rear ones nd my other front one does not do this? I've tried everything I can think of. What should I do?
#5887
I've tried pushing on the axle cup. Maybe the aluminum hex adapter wasn't maachined deep enough for the hardened pin to go in deep enough?
#5888
Tech Fanatic
Originally posted by SupermaxxRich
I assembled my front knuckles tonight. On one of them, even with the wheel on and nut tightened, I can grab the wheel and move it back and forth about 0.3mm. This doesn't seem right because my rear ones nd my other front one does not do this? I've tried everything I can think of. What should I do?
I assembled my front knuckles tonight. On one of them, even with the wheel on and nut tightened, I can grab the wheel and move it back and forth about 0.3mm. This doesn't seem right because my rear ones nd my other front one does not do this? I've tried everything I can think of. What should I do?
I put the shims already.
Use .2 dont use .3mm, small play is good for bearing health.
#5889
Originally posted by SupermaxxRich
I assembled my front knuckles tonight. On one of them, even with the wheel on and nut tightened, I can grab the wheel and move it back and forth about 0.3mm.
I assembled my front knuckles tonight. On one of them, even with the wheel on and nut tightened, I can grab the wheel and move it back and forth about 0.3mm.
#5890
Originally posted by vadn1
Can someone point out any place selling a 710 kit new in box for $350.
Can someone point out any place selling a 710 kit new in box for $350.
#5891
Re: Re: Re: One just for InitialD
Originally posted by InitialD
Same sentiments ! I think I told Mark how I felt about the whole thing on PM sometime back if I'm not mistaken.
Same sentiments ! I think I told Mark how I felt about the whole thing on PM sometime back if I'm not mistaken.
In F3 he was mega quick - I saw him overtake a guy on the outside of a turn on the last lap - it look like he was going to spear off the track big style, but somehow he got around the guy - it was the most impressive piece of driving I have seen in F3.
Unfortunately, shortly after this Alex had a very big accident at Spa - he was luckly he wasn't killed! After this accident he was never really the same again. Personally, although he never mentioned it, I think this affected him really badly - I'm not surprised either!!
The step up to F1 was wrong for him, perhaps if he'd had a couple more years in F3000, he would have settled down.
End of speech
#5892
Knuckle is not installed on car yet. I can grab the "axle cup" the thing with the threads for the wheels. I can grab that and wiggle it 0.6mm back and forth. I just measured it. I even put the wheel on and its the same thing.
#5893
I measured the depth of the groove that is machined into the aluminum wheel hex adapter and both are the same depth. So there must be something else off? I'll try and measure both knuckles to see if they are the same thickness??
#5894
Originally posted by InitialD
Where are you at? Have you tried www.RC-Mushroom.com?
Where are you at? Have you tried www.RC-Mushroom.com?
#5895
Originally posted by markp27
Whilst you're at it D, can you point me to somewhere, where they're selling the 710 for $50?
Whilst you're at it D, can you point me to somewhere, where they're selling the 710 for $50?