1LikesMugen MTX-4R
11-11-2008, 08:59 AM
#2311
Is this at the Toledo track? I have a realy good set-up for that track.
If you are talking about the Toledo track, it's all about the way you setup for the sweeper. You can go thru the sweeper with out lifting, but if you miss you will pay for it!!!
Later,
Ira
P.S. Is it cold there yet, shur is here.
If you are talking about the Toledo track, it's all about the way you setup for the sweeper. You can go thru the sweeper with out lifting, but if you miss you will pay for it!!!
Later,
Ira
P.S. Is it cold there yet, shur is here.
What's up Ira?
I like the last part of your sig! Cant wait for the Winternats
11-23-2008, 04:04 PM
#2314
Mtx4 and the mtx4r (difference) parts
Whats up? I was wondering whats the difference between the mtx4 and the mtx4r,whats was added to the R thats not on the 4 far as upgrades and if possible if anybody know the part numbers and the best place to purchase these items and did the chasis change too or are they the same,thanks and hopefully I can get some help with this from bumper to bumper so I can upgrade my Mugen mtx4 to make it an R
11-24-2008, 06:08 AM
#2316
Whats up? I was wondering whats the difference between the mtx4 and the mtx4r,whats was added to the R thats not on the 4 far as upgrades and if possible if anybody know the part numbers and the best place to purchase these items and did the chasis change too or are they the same,thanks and hopefully I can get some help with this from bumper to bumper so I can upgrade my Mugen mtx4 to make it an R
in regards to geometry, just switch the front uprights and the rear camber susppension mount and that;s it
11-30-2008, 08:37 PM
#2319
12-01-2008, 09:56 AM
#2322
You're correct, Acer Bearings have Ceramics for both On-Road and Off-Road. The one you need for MTX4-R is Part or Product Number : CM10
Like this:
http://www3.towerhobbies.com/cgi-bin...?&I=LXTNY5&P=7
They are good bearings!
12-01-2008, 10:28 AM
#2323
Whats up? I was wondering whats the difference between the mtx4 and the mtx4r,whats was added to the R thats not on the 4 far as upgrades and if possible if anybody know the part numbers and the best place to purchase these items and did the chasis change too or are they the same,thanks and hopefully I can get some help with this from bumper to bumper so I can upgrade my Mugen mtx4 to make it an R
Here are the list of parts differentiating the MTX-4 kit with the MTX-4R:
1. Aluminum Wheel Hub : Part# T0142
2. Front Lower Arm : Part# T0151-B
3. Rear Upper Arm Mount : Part# T0161
4. Front Upright (2°) : Part# T0164
5. Front Universal Joint : Part# T0245
6 .Front Belt (Rubber) : Part# T0268
7. Rear Belt (Rubber) : Part# T0269
8. Side Belt (Rubber) : Part# T0270
9. Rear Universal Joint : Part# T0274
10. Front One-Way Drive Axle : Part# T0276
11. Ventilated Brake Disk : Part# H0369
12. Aluminum Engine Mount : Part# T0717
As far as where to purchase them : www.kamikazetoysandhobbies.com . I suggest calling them direct at (714) 997-8697
Hope this helps,
12-01-2008, 11:00 AM
#2324
i think the best bearings are boca bearings. my lhs supplies a kit which is made specially for him, and the kit includes the set for mtx4/mrx4. they are orange seal ceramic hybrid bearings which has the grade 5 ceramic Si3N4 balls, and ABEC 7 tolerances.(best bearing of boca) I was told that they are OILED FOR LIFE. price is high though. 16$ a piece
