1/10 Sedan Quick Release wheels
09-21-2006, 09:41 AM
#46
front 198mm & rear 198mm
09-21-2006, 09:44 AM
#47
710
yes I did it myself & the custom 200mm car thats a few poast up . I am working on the 720 as wee speak ...
09-21-2006, 10:35 AM
#48
Originally Posted by Got the grip
yes I did it myself & the custom 200mm car thats a few poast up . I am working on the 720 as wee speak ...
09-21-2006, 10:59 AM
#49
Originally Posted by Marcos.J
its very simple I did this 6 years ago with the Serpent Impulse all you need is the front axles from the serpent Impact since they use the same bearings. I used the Impact axles and dogbones
09-21-2006, 11:25 AM
#50
Originally Posted by Marcos.J
its very simple I did this 6 years ago with the Serpent Impulse all you need is the front axles from the serpent Impact since they use the same bearings. I used the Impact axles and dogbones
Do you have any photos of your impulse with clip on wheels..
Here are some photos of my impulse pro .with clip on wheels..from back in the day
09-21-2006, 11:38 AM
#51
I have even put the clip on wheels on a 705 ..Here are some photos ..
09-21-2006, 11:41 AM
#52
You must like Serpent cars 
.
09-21-2006, 11:45 AM
#53
Originally Posted by Jo Gutierrez
You must like Serpent cars .YES ONLY the BEST !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!l
09-21-2006, 12:02 PM
#54
Originally Posted by Jo Gutierrez
You must like Serpent cars .I Like serpent so much I even made a 2-wheel drive out of there parts to run at a Velodrome. It also is 200mm & has clip on wheels . It will do 70 plus mph
09-21-2006, 12:33 PM
#55
Originally Posted by Got the grip
Do you have any photos of your impulse with clip on wheels..
Here are some photos of my impulse pro .with clip on wheels..from back in the day
Here are some photos of my impulse pro .with clip on wheels..from back in the day
09-21-2006, 01:39 PM
#56
Quick Release
I recall Bill Christensen in the Phoenix Area had done the same thing about 3 years ago. He has basically had every Serpent Type vehicle that has been produced and figured it out. It seemed to work very well.
I do not recall all the particulars, however, since I just noticed this thread, I think it would be cool to have some of the manufacturers "or" aftermarket inventors like yourself get these out on the market.
Anything but the standard Hex Bolt setup !!!
I do not recall all the particulars, however, since I just noticed this thread, I think it would be cool to have some of the manufacturers "or" aftermarket inventors like yourself get these out on the market.
Anything but the standard Hex Bolt setup !!!
09-22-2006, 03:07 PM
#57
As mentioned Team Magic has made the quick release wheels. With theirs you have a large bearing in the hub carrier to accommodate the the quick release shaft. The wheels themselves are made stronger to insure there is no bends or breaks during use.
I would like to see this size become standard so no matter what tire is your preference it will still work any car manufacturer.
SamF
I would like to see this size become standard so no matter what tire is your preference it will still work any car manufacturer.
SamF
09-22-2006, 11:03 PM
#59
Originally Posted by FREELANCE_RCer
For tire quick release.
Hope they also makes an arbor for the tire truer too.
Hope they also makes an arbor for the tire truer too.
Good point !
Innovation is the future of rc ,and i am confident this is a innovationn that is going to change a few minds and hopefully become popular as its just so much easier to work with.
They might not be the first to do this but they are the first manufacturer to impliment it and market it.
Last edited by razzor; 09-23-2006 at 11:25 AM.
