Serpent 720
#4171
bump..........news>?
#4172
Tech Adept
DJ,,very nice report on ROAR Nat's,,,thank you!!
#4173
Tech Elite
#4174
Tech Elite
iTrader: (101)
Very Nice showing DJ at the nats to you and Paolo. I was really hoping that you guys would go 1 and 2. You'll get them next time for sure. I really wanted to thank you though for the great report you posted for us to read. I know that takes time to do, so thanks for that!
Are you going to be sending in a set up sheet for that race to Serpent.
Steve
Are you going to be sending in a set up sheet for that race to Serpent.
Steve
#4177
Tech Elite
Very Nice showing DJ at the nats to you and Paolo. I was really hoping that you guys would go 1 and 2. You'll get them next time for sure. I really wanted to thank you though for the great report you posted for us to read. I know that takes time to do, so thanks for that!
Are you going to be sending in a set up sheet for that race to Serpent.
Steve
Are you going to be sending in a set up sheet for that race to Serpent.
Steve
DJ Apolaro
#4179
loosen, u might wanna check ur clutch gap and end play after.
#4180
[QUOTE=fly_wheel;4952175]heard the new 720-09 is coming next year... hopefully, just like 720 ~ 720-07 ~ 720-08... nothing much changes except some additional option parts...[/QUOTE
i hope they dont change much, but then again. i am due for a new 720. lets see what happens..
i hope they dont change much, but then again. i am due for a new 720. lets see what happens..
#4181
Tech Elite
iTrader: (19)
I will send one in to get posted for you guys. It is not much different than my last set-up. However I did use a front diff this time (and liked it) and used less rear droop, and the #2 postion in the rear roll center. I also used the middle position for the front roll center. I went from 4 to 5 droop in the rear and 0 in the front. I also ran a lot more rear toe 3 degree. The front diff had serpent 80,000. The traction was very weird and I needed a more stable car. That is why I ran more toe in the rear, lower rear roll center and less droop for more stable breaking.
DJ Apolaro
DJ Apolaro
#4182
Tech Elite
hi DJ, i have just put a diff in mine, when i installed it, i notice only one guide for the belt on the geared diff. i shimmed out the inner layshaft pulley to align the belt better on the diff. did you do anything like that, if i didnt do so, the belt would run right on the edge of the teeth on the diff side. just curious ? cheers.
DJ
#4183
Tech Elite
iTrader: (19)
well i didnt have any problems with it this weekend. i checked it after every run, the belt stayed where is was first located. i had a few hits, no problems though. but still i like the car with the front swaybar disengaged. seems to provide better turn in, and with the diff, better again.
#4184
Mr Dj Apolaro,
I need your help for a setup on the 720,
Our track is small, technical with low-to-medium speed, quick direction changes. The track is super flat, however the traction is rather low.
Can you please recommend me a setup to begin with? Mainly i am facing understeer problems at mid corner and corner exit.
My current setup is attached,
I would appreciate any help,
Thank you,
I need your help for a setup on the 720,
Our track is small, technical with low-to-medium speed, quick direction changes. The track is super flat, however the traction is rather low.
Can you please recommend me a setup to begin with? Mainly i am facing understeer problems at mid corner and corner exit.
My current setup is attached,
I would appreciate any help,
Thank you,
#4185
One correction, my main problem is oversteer and not understeer but generally the car seems to be unstable.