Serpent 720
#916
It worth... Now we have the correct answer to camber-rise Thx!
#917
Originally Posted by rcpanama
You can see in this picture how I did the instalation I have in the 720 a 1,oo VXR LiPo, you have to cut the size of the battery holder, you will not be able to install the holder from behain of the chassis, only from the top, but that is no sacrfice for what you get, the Voltage Regulator yoy have to install it on the size of the car with a plstic holder.
http://www.rctech.net/forum/attachme...hmentid=156154
In 3hobby their is a very good article
http://3hobby.net/modules.php?name=C...howpage&pid=61
RCPANAMA
http://www.rctech.net/forum/attachme...hmentid=156154
In 3hobby their is a very good article
http://3hobby.net/modules.php?name=C...howpage&pid=61
RCPANAMA
#919
Originally Posted by rcpanama
Last picture
RCPANAMA
RCPANAMA
#920
Originally Posted by buboy28
hi, would somebody please post a picture of how they were able to use the VXR Lipo batts with the 720 might as well see how you guys do it before i cut anything with the 720 receiver battery holder
This was done on the 710 but obviously its the same for the 720.
#921
Originally Posted by rcpanama
...
In 3hobby their is a very good article
http://3hobby.net/modules.php?name=C...howpage&pid=61
RCPANAMA
In 3hobby their is a very good article
http://3hobby.net/modules.php?name=C...howpage&pid=61
RCPANAMA
#922
Originally Posted by buboy28
ok, thank you very much will do the same thing as you did one more thing are you guys still using an on and off switch
#923
Tech Adept
The silence in this thread now is deafening...
So... to get things going again; I'm painting (with rattle cans) a new mazda 6 body but I'm out of ideas... please help
So... to get things going again; I'm painting (with rattle cans) a new mazda 6 body but I'm out of ideas... please help
#925
Tech Fanatic
iTrader: (1)
Originally Posted by Qlone
The silence in this thread now is deafening...
So... to get things going again; I'm painting (with rattle cans) a new mazda 6 body but I'm out of ideas... please help
So... to get things going again; I'm painting (with rattle cans) a new mazda 6 body but I'm out of ideas... please help
Try going up the side at a 45 angle with 1/4 inch tape and then flames on the front. I know its played out but my imagination doesn't stretch that far anymore with rattle cans
#926
Tech Addict
iTrader: (1)
Took the 720 for a shake down run today. Had to change a couple of settings but more will need to be done at an actual race meeting.
- Had to loosen the clutch preload spring to about .75mm
- 2 speed tension screws in 1.5 turns from the kit setup
- Had some brake binding, but seems to be getting better. Anyone using a return spring on the brake.
#927
Originally Posted by B4
[*]Had some brake binding, but seems to be getting better. Anyone using a return spring on the brake.[/list]
RCPANAMA
#928
HTML Code:
You can see in this picture how I did the instalation I have in the 720 a 1,oo VXR LiPo, you have to cut the size of the battery holder, you will not be able to install the holder from behain of the chassis, only from the top, but that is no sacrfice for what you get, the Voltage Regulator yoy have to install it on the size of the car with a plstic holder.
Jim
#929
Originally Posted by J.Wright
HTML Code:
You can see in this picture how I did the instalation I have in the 720 a 1,oo VXR LiPo, you have to cut the size of the battery holder, you will not be able to install the holder from behain of the chassis, only from the top, but that is no sacrfice for what you get, the Voltage Regulator yoy have to install it on the size of the car with a plstic holder.
Jim
#930
Thanks Bro.
Jim
Jim