Jammin JPX 21 Plus ( new)
11-08-2009, 06:11 PM
#136
[QUOTE=j053 has worked best so far and will try 2035 maybe tomorrow.[/QUOTE]
wow really? what kind of runtime were u getting with the 053? i cant get no more the 7 min. im switching here reallly soon.
how well does the JP3 pipe do on the jammin? what kind of runtime?
wow really? what kind of runtime were u getting with the 053? i cant get no more the 7 min. im switching here reallly soon.
how well does the JP3 pipe do on the jammin? what kind of runtime?
11-09-2009, 01:20 PM
#137
bump
how well does the JP3 pipe do on the jammin? what kind of runtime?
how well does the JP3 pipe do on the jammin? what kind of runtime?
11-09-2009, 01:44 PM
#138
Tech Addict
I have run many diff pipes on this mill.The jp3 runs good but run time sucks.IMO the best pipe for this mill is the TTR 2035 carbon shoes 0.9 clutch springs hot plug and remove head shim with 7mm carb insert.This combo will get you 10 min run time and is smooth and powerful.
11-09-2009, 01:47 PM
#139
Tech Addict
If you can handle the power the 086 rocks But i like the 2035 much better it is a lot smoother better run time and is very crisp running.
11-09-2009, 02:53 PM
#140
isnt the 086 a top end pipe? how would that create more power (on the low end) or is it only on the top end? bc the 053 pipe i have says its a low end pipe and there is a lot of low end power. but i am looking for runtime not power. thats a thing im not worried about with the jammin is the low end power bc it has plenty lol. and why is the 2035 so freaking expensive???
11-09-2009, 03:01 PM
#141
Tech Addict
isnt the 086 a top end pipe? how would that create more power (on the low end) or is it only on the top end? bc the 053 pipe i have says its a low end pipe and there is a lot of low end power. but i am looking for runtime not power. thats a thing im not worried about with the jammin is the low end power bc it has plenty lol. and why is the 2035 so freaking expensive???
11-09-2009, 03:05 PM
#142
what brand 2035? AE? and what kind of run times can u get? like 9 min? 10 min?
11-09-2009, 04:37 PM
#143
Tech Addict
11-19-2009, 06:33 AM
#144
Any tips i can use on the jammin .28?
11-19-2009, 07:15 AM
#145
11-19-2009, 09:48 AM
#146
I have a Jammin JPX.21, it has about a gallon and half since mod, sleeve and piston was replaced by RBMods, motor runs terrific tons of power and torque, avg run times of 8-8 1/2 minutes.
More than enough power for buggy and truggy, comes with original bow and manual.
175.00, shipped to the lower 48.
More than enough power for buggy and truggy, comes with original bow and manual.
175.00, shipped to the lower 48.
11-23-2009, 11:58 AM
#148
11-23-2009, 01:06 PM
#149
11-23-2009, 01:10 PM
#150
I personally much prefer the JPX..... I find the +4 to be really lacking in the power department, especially in Truggy...next to the jammin's I'm used to the +4 feels like a dog..... Not that the +4 is a bad engine as its is a very good engine, but its power output is nowhere near that of the Jammin, not even remotely close....
