R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Nitro Off-Road

Reply
 
Thread Tools Search this Thread
Old 08-19-2009, 08:28 PM   #1
Tech Initiate
 
Join Date: Aug 2009
Location: jeffersonville,IN
Posts: 20
Trader Rating: 1 (100%+)
Default heed help on a back plate for my .26 dynamite

hey guys i bought a .26 dynamite truggy motor to run in my kyosho strr. And it came with pull/spin start it hangs down to low for the motor mount the start hits the chassis before the motor hits the motor mount so i was wondering if you could help me on choosing the backplate.

i think i picked out the right one but i want to make sure before i order one .it says its good for the mach 26 i would think that the bore and back plate size would be the same.. please let me know what ya think..thanks for looking at my post.
ps it wont let me post the url yet
Happy bashing and racing

Mike BeMiller
__________________
2nd place is a first place loser!
kyoshoracer.26 is offline   Reply With Quote
Old 08-19-2009, 08:38 PM   #2
Tech Fanatic
 
aaron joy's Avatar
 
Join Date: Oct 2007
Location: New Jersey
Posts: 825
Trader Rating: 16 (94%+)
Default

Is this the one you are talking about if so you have to cut the one-way bearing knub off the crankshaft.
http://www.dynamiterc.com/Products/D...ProdID=DYN0922
aaron joy is offline   Reply With Quote
Old 08-19-2009, 08:54 PM   #3
Tech Initiate
 
Join Date: Aug 2009
Location: jeffersonville,IN
Posts: 20
Trader Rating: 1 (100%+)
Default

Thanks Aaron thats the one how far back should i cut it back?
__________________
2nd place is a first place loser!
kyoshoracer.26 is offline   Reply With Quote
Old 08-19-2009, 09:37 PM   #4
Tech Adept
 
casterdriver's Avatar
 
Join Date: Dec 2007
Location: Cibolo Texas
Posts: 204
Default

if you can find one............... sportwerks swk8057 is a direct fit. has a groove so no cutting.

Here is a pic of it.....http://www.horizonhobby.com/Products...ProdID=SWK8057

they were discontinued when they killed sportwerks but if you look around you can find them............. Or look for that dyn0960 part #..... its the new dynamite part#. same part.
__________________
Mugen MBX7/WERKS CRE-B6,Stock B6,Stock B2/Werks 2013,2057,2058
RC10GT2-FT, Dynamite Platinum .12
VP-Racing Powermaster 20% and 30% Race Fuel
Official NON-EXPERT

Last edited by casterdriver; 08-19-2009 at 09:49 PM.
casterdriver is offline   Reply With Quote
Old 08-19-2009, 10:50 PM   #5
Tech Fanatic
 
aaron joy's Avatar
 
Join Date: Oct 2007
Location: New Jersey
Posts: 825
Trader Rating: 16 (94%+)
Default

No problem. If I were you I would order the one casterdriver recommended. Dynamite's page says early Sept. If you can't wait and don't mind taking your engine apart, then you want to cut the knub off flush with the back of the conrod. There should be a step down on the crank pin showing you how much to cut off.
aaron joy is offline   Reply With Quote
Reply



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 07:56 AM.


Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net