R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Nitro Off-Road

Reply
 
Thread Tools Search this Thread
Old 04-23-2009, 08:52 AM   #1
Tech Adept
 
drebies_one's Avatar
 
Join Date: Nov 2008
Location: saratoga,ny
Posts: 125
Default anyone with tmaxx experience...please help

ok....i have alot of play where my universials,go thru my axle carriers....i can tighten all i want and the tire still wobbles.....i am using 17 mm axial beadlockers....wich isnt the problem.....and i have the rpm axial carriers....i have links below to what i have st up on my truck....when i put the new axle carriers on im pretty sure i used the oversized bearings that came with the knucks.....but still lots of play....i may have for some reason used older bearings,trying to conserve where i can....but cant seem to find a set of these oversized bearing in my stuff,wich leads me to believe i used the new oversized ones.....anyway,apparently i cannot just get the bearings,i have to buy all the axle carriers again.....anyone with tmaxx experience have any advice,or where,or how big i need bearings....or anyway to fix this play/wobble going on?
anyway these links are what i have on my truck right now.
rpm knucks
http://www.rpmrcproducts.com/product...ires/80585.htm
traxxas universals
i have the 17mm conversion on there as well...
http://traxxas.com/products/nitro/ma...ories/cvds.jpg

this is the last thing wrong on my truck then she will be mint....dropped the .26 picco in her,and she is an animal.....well was reving out of control,until i realized i put the throttle linkage on wrong....*note(read your manuals,study the exploded views....look at how others is set up...hahah)every mistake i made building all my tmaxxes were stupid obvious mistakes.....now i know how to run and tune a nitro engine....time to figure out how to rip em apart,and make em go faster.......oops went off topic there...anyway any tmaxx people on here any help would be awesome....thanks
drebies_one is offline   Reply With Quote
Old 04-23-2009, 09:01 AM   #2
Tech Adept
 
Join Date: Mar 2009
Location: berwick PA
Posts: 241
Trader Rating: 3 (100%+)
Default

a little tire wobble is normal.
your problem lies in the axles that come through the spindle.
that little pin that goes trough you wheel axle is too far from the bearings which wil give you tire wobble. you get it on all traxxas cars/trucks.
i have a revo and a rustler that do that also. all you can do is balance your wheels so you dont really see it while driving.
i also found out that you cant drill another hole in the axle to comensate for the slack.
its about a half of a hole off, if you understand what im trying to say.
jaredmausteller is offline   Reply With Quote
Old 04-23-2009, 05:40 PM   #3
Tech Adept
 
drebies_one's Avatar
 
Join Date: Nov 2008
Location: saratoga,ny
Posts: 125
Default

Quote:
Originally Posted by jaredmausteller View Post
a little tire wobble is normal.
your problem lies in the axles that come through the spindle.
that little pin that goes trough you wheel axle is too far from the bearings which wil give you tire wobble. you get it on all traxxas cars/trucks.
i have a revo and a rustler that do that also. all you can do is balance your wheels so you dont really see it while driving.
i also found out that you cant drill another hole in the axle to comensate for the slack.
its about a half of a hole off, if you understand what im trying to say.
im a little lost...but my friends with the same set up are all good.....im not trying to buy another 2 sets of axle carriers.....i think i should just measure the bearing and go from there...
drebies_one is offline   Reply With Quote
Old 11-07-2009, 08:04 AM   #4
Tech Adept
 
drebies_one's Avatar
 
Join Date: Nov 2008
Location: saratoga,ny
Posts: 125
Default

Quote:
Originally Posted by drebies_one View Post
im a little lost...but my friends with the same set up are all good.....im not trying to buy another 2 sets of axle carriers.....i think i should just measure the bearing and go from there...

ok i follow now...heh
problem solved..it was actually a problem with the pivot balls.
i did not have them seated right in the carrier.
drebies_one is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
RDlogics gas tank leaking...tmaxx drebies_one Monster Trucks 13 05-13-2009 09:41 PM
Northwest Championship Tour, I B RACIN Northwest Racers 1297 05-13-2007 07:11 PM



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 07:38 PM.


Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net