Adam Drake talks about the new 8ight 2.0
11-14-2008, 11:32 PM
#226
you hadn't posted what servos your using so it was the only thing I thought maybe causing the problem.
Hope you get it sorted
Adrian
11-15-2008, 07:38 AM
#227
11-15-2008, 09:04 AM
#228
Tech Adept
What needs to be done ?
Moved mesaage to the Eight 2.0 thread
Last edited by losi8lunie; 11-16-2008 at 08:42 AM. Reason: In wrong thread
11-18-2008, 12:38 PM
#229
http://www.upgradercshop.com/mm5/mer...mvc?Screen=VID
Some good random vids of the losi crew in action at Hotrods...
Some good random vids of the losi crew in action at Hotrods...
11-19-2008, 01:45 PM
#230
Fluke- No plans for a conversion kit. email me your address [email protected]
bustedpiecerc- It sounds like the low seed needle is too lean or your clutch springs are too light.
aburton- See you soon!
chill will- Yes, but you also need to change the side gaurds and linkage.
brian kadow- ?
briguy- Radio tray, and linkage.
TIX- Yes, but you will need to drill the outer rear hinge pin hole on the arm to 3.5mm.
bustedpiecerc- It sounds like the low seed needle is too lean or your clutch springs are too light.
aburton- See you soon!
chill will- Yes, but you also need to change the side gaurds and linkage.
brian kadow- ?
briguy- Radio tray, and linkage.
TIX- Yes, but you will need to drill the outer rear hinge pin hole on the arm to 3.5mm.
11-19-2008, 01:55 PM
#231
Tech Fanatic
Just havin some fun with Burton & Chill Will. 
11-19-2008, 02:05 PM
#233
hey burton its laquan
are you guys upgrading your 8t with 2.0 parts
if so whats the parts list
are you guys upgrading your 8t with 2.0 parts
if so whats the parts list
11-19-2008, 02:18 PM
#235
Tech Fanatic
11-19-2008, 03:36 PM
#236
Fluke- No plans for a conversion kit. email me your address [email protected]
bustedpiecerc- It sounds like the low seed needle is too lean or your clutch springs are too light.
aburton- See you soon!
chill will- Yes, but you also need to change the side gaurds and linkage.
brian kadow- ?
briguy- Radio tray, and linkage.
TIX- Yes, but you will need to drill the outer rear hinge pin hole on the arm to 3.5mm.
They want you to buy a new kit even if you just bought the 8ight. I know it's not Drakes fault, but I thought I would just put in my 2 cents.
11-19-2008, 03:47 PM
#237
11-20-2008, 07:23 PM
#238
Bigedmond- It’s possible if sales take off. I would rather run truggy personally.
Intergra- Haha..
TIX- The material, mold configuration, design and molding process.
R1harper- Thanks!
Mr. losi- 2-a front and 2-b rear.
Merciless- My buggy was a little over 2 oz. lighter.
Dirtydezpirate- I’ll be at Revelation tonight and Thursday if you need help. What was the engine running at before you switched fuel?
Blower Uper A I haven’t used a nosram or hpi engine.
Donut92673- No problem. Let me know how it runs this weekend.
Jamminfrazy- I’m sure we will release a new turggy at some point, but I don’t know when that will be.
Bigedmond- WOW, 403!
Intergra- Haha..
TIX- The material, mold configuration, design and molding process.
R1harper- Thanks!
Mr. losi- 2-a front and 2-b rear.
Merciless- My buggy was a little over 2 oz. lighter.
Dirtydezpirate- I’ll be at Revelation tonight and Thursday if you need help. What was the engine running at before you switched fuel?
Blower Uper A I haven’t used a nosram or hpi engine.
Donut92673- No problem. Let me know how it runs this weekend.
Jamminfrazy- I’m sure we will release a new turggy at some point, but I don’t know when that will be.
Bigedmond- WOW, 403!
11-21-2008, 01:05 AM
#239
Tech Apprentice
try turning the HSN a little more. Maybe around 1/2 turn and see how it goes. You can always lean it slowly if its too fat.
11-21-2008, 02:01 AM
#240
hey adam i have a quick question and a problem.
how often are u at the nitro pit in az??? i just started racing not long ago and would like 2 see u and mike race, im going 2 tucson this weekend for "The Az Champ series"
and here is my problem. i have the original losi 8ight, i do plan to get the 2.0 but im tight on money because of this problem. i have gone thru 4-5 clutches in the past month, month in a half.My clutch bearings are lasting a night of racing and thats it. i have finally started changing the bearings after a night of racin but i dont feel this should be doing this. ive had 2 different hobby shops take a look but they dont know why. i was runnin the pro kits clutch set up but now i changed to all alum. pads and silver springs hoping this will help
how often are u at the nitro pit in az??? i just started racing not long ago and would like 2 see u and mike race, im going 2 tucson this weekend for "The Az Champ series"
and here is my problem. i have the original losi 8ight, i do plan to get the 2.0 but im tight on money because of this problem. i have gone thru 4-5 clutches in the past month, month in a half.My clutch bearings are lasting a night of racing and thats it. i have finally started changing the bearings after a night of racin but i dont feel this should be doing this. ive had 2 different hobby shops take a look but they dont know why. i was runnin the pro kits clutch set up but now i changed to all alum. pads and silver springs hoping this will help
