TQ Racing SX8
11-21-2008, 09:13 AM
#812
Doc and I will be there as well!
Brian, did you get my email earlier this week?
Thanks
Brian, did you get my email earlier this week?
Thanks
11-21-2008, 09:27 AM
#813
Tech Fanatic
I will get back to you taday. Did you get your buggy?
11-21-2008, 10:29 AM
#814
11-21-2008, 10:36 AM
#815
Tech Fanatic
iTrader: (22)
-jesussaves-
i found the steering tie rod ends were binding the pivot ball on the steering knuckle to bind . took it off and squeezed the plactic a bit, freed it right up.
i noticecd on the servo saver shaft(threaded tube). the beaing sits about .005 out of the tube. the tube was bored to a depth of .113 and the bearings over length is .118
taking it in to work tonight to bore it to depth so that the bearing will sit about .002 below flush
i found the steering tie rod ends were binding the pivot ball on the steering knuckle to bind . took it off and squeezed the plactic a bit, freed it right up.
i noticecd on the servo saver shaft(threaded tube). the beaing sits about .005 out of the tube. the tube was bored to a depth of .113 and the bearings over length is .118
taking it in to work tonight to bore it to depth so that the bearing will sit about .002 below flush
11-21-2008, 10:42 AM
#816
Tech Fanatic
Chill Will, give me a haalllllaaaaa ASAP!
11-21-2008, 01:46 PM
#818
Tech Regular
-jesussaves-
i found the steering tie rod ends were binding the pivot ball on the steering knuckle to bind . took it off and squeezed the plactic a bit, freed it right up.
i noticecd on the servo saver shaft(threaded tube). the beaing sits about .005 out of the tube. the tube was bored to a depth of .113 and the bearings over length is .118
taking it in to work tonight to bore it to depth so that the bearing will sit about .002 below flush
i found the steering tie rod ends were binding the pivot ball on the steering knuckle to bind . took it off and squeezed the plactic a bit, freed it right up.
i noticecd on the servo saver shaft(threaded tube). the beaing sits about .005 out of the tube. the tube was bored to a depth of .113 and the bearings over length is .118
taking it in to work tonight to bore it to depth so that the bearing will sit about .002 below flush
Good work
, tell us how the car handles after the mod in regard to steering... When I was giving the buggy a once over I noticed the bearing just wasn't seated properly, but I was more concerned about the 4*16 Kingpin screw popping off. If you or anyone for that matter find a mod to fix the 4*16 king pin screw make sure post some pics and let us all know, this must be fixed. 
11-21-2008, 02:50 PM
#819
JP-6 Pipe
Has anyone had any firsthand experience with the Jammin JP-6 pipe yet? I've got one coming that will be mated up to a V-Spec, and was just curious of other peoples opinions. Oddly, from the pictures I've seen, it looks a lot like the O.S. pipe.
Thanks,
Richard
Thanks,
Richard
11-22-2008, 08:41 AM
#821
Tech Fanatic
11-23-2008, 06:43 PM
#824
Trey and I will be heading out to the JConcepts RC Clash soon.
Any other TQ Drivers/Vehicles are going?
We are going to bring home a trophy for TQ.
Any other TQ Drivers/Vehicles are going?
We are going to bring home a trophy for TQ.
11-24-2008, 06:59 AM
#825
Tech Fanatic
I will be going to the Thanksgiving Thunder race the 28th & 29th.