OCM KAOS DOMINATING
01-07-2008, 08:27 PM
#781
Tech Regular
yea im still going into the NSW state titles, yea it does with a new body and all other stuff, ive only had the buggy since Oct. has done about 5runs now.
01-08-2008, 06:01 AM
#782
Guys, if you are interested in saving money on parts, tires, fuel, etc send me a email. I'll fill you in on some great offers
[email protected]
[email protected]
01-08-2008, 04:44 PM
#784
Nick Sartor's OCM Kaos Setup
--------------------------------------------------------------------------------
Front...
Upper arm insert..... 1.0 hole up, 2mm shims above upper arm mount
Lower arm position(anti-dive).....1.0 hole down
Front inboard toe-in position.....0
Steering knuckle position.....lower hole
Anti-roll bar(sway bar).....Stock
Upper arm Spacer.....All shims in front of arms
Camber angle.....-2 deg.
Toe angle.....+2 1/2 deg.
Steering Ackerman Location.....Center Hole
Shock Locations.....Inside Hole at Tower and Outside Hole on Arms
Shock Oil.....Trinity 60wt
Shock Pistons.....1.4x4
Springs.....OCM Blue
Diff.....5k
Center.....
Diff.....5k
Rear.....
Toe Block.....Stock
Toe-in Angle.....1.25 Out
Anti-Squat.....0
Upper Arm Location at Upright.... Center Hole
Upper Arm Location at Tower.....Inside Lower Hole
Upright Pin Position.....Lower Hole
Wheelbase....All Shims behind Hub
Camber.....-2 deg.
Shock Locations.....Middle Hole at Tower and Inside Hole at Arms
Shock Oil.....Trinity 60wt
Shock Piston.....1.4x4
Springs.....OCM Blue
Diff.....3k
I run on a hard packed clay track and i run Panther Switch 2.0 clay compound on all four corners
--------------------------------------------------------------------------------
Front...
Upper arm insert..... 1.0 hole up, 2mm shims above upper arm mount
Lower arm position(anti-dive).....1.0 hole down
Front inboard toe-in position.....0
Steering knuckle position.....lower hole
Anti-roll bar(sway bar).....Stock
Upper arm Spacer.....All shims in front of arms
Camber angle.....-2 deg.
Toe angle.....+2 1/2 deg.
Steering Ackerman Location.....Center Hole
Shock Locations.....Inside Hole at Tower and Outside Hole on Arms
Shock Oil.....Trinity 60wt
Shock Pistons.....1.4x4
Springs.....OCM Blue
Diff.....5k
Center.....
Diff.....5k
Rear.....
Toe Block.....Stock
Toe-in Angle.....1.25 Out
Anti-Squat.....0
Upper Arm Location at Upright.... Center Hole
Upper Arm Location at Tower.....Inside Lower Hole
Upright Pin Position.....Lower Hole
Wheelbase....All Shims behind Hub
Camber.....-2 deg.
Shock Locations.....Middle Hole at Tower and Inside Hole at Arms
Shock Oil.....Trinity 60wt
Shock Piston.....1.4x4
Springs.....OCM Blue
Diff.....3k
I run on a hard packed clay track and i run Panther Switch 2.0 clay compound on all four corners
01-08-2008, 10:05 PM
#785
Tech Regular
porter, the MBX5 will fit the buggy fine, thats what i have now and it looks sweet.
01-08-2008, 10:05 PM
#786
Tech Regular
porter, the MBX5 will fit the buggy fine, thats what i have now and it looks sweet.
01-10-2008, 01:51 AM
#788
Tech Regular
Bump. can you post pics of the carbon fiber parts available please.
01-10-2008, 06:52 AM
#789
carbon parts of Kevin in Australia
01-10-2008, 06:54 AM
#790
guys who are onto SGRID
I think sgrid 2007 is closed now
we will have to lock in again
in sgrid 2008
http://www.rc-racing.com/cgi-bin/pw/...csel=@1&cpass=
I think sgrid 2007 is closed now
we will have to lock in again
in sgrid 2008
http://www.rc-racing.com/cgi-bin/pw/...csel=@1&cpass=
Last edited by speedy2; 01-10-2008 at 01:48 PM.
