R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Nitro Off-Road

Reply
 
Thread Tools Search this Thread
Old 08-09-2007, 09:23 AM   #1
Tech Adept
 
PRScustom's Avatar
 
Join Date: Jul 2007
Posts: 150
Trader Rating: 5 (100%+)
Default Pipe for new engine

I am going to buy the new O.S. .28 truggy motor and was wondering what pipes you guys run on .28's. I was thinking about a JP-3, but would like some feedback or opinions. Thanks.
PRScustom is offline   Reply With Quote
Old 08-09-2007, 07:27 PM   #2
Tech Elite
 
Jason Halvorson's Avatar
 
Join Date: Apr 2007
Location: Grand Forks ND
Posts: 3,955
Trader Rating: 22 (100%+)
Send a message via AIM to Jason Halvorson Send a message via MSN to Jason Halvorson
Default

IMO JP1 is the best for truggy...
Jason Halvorson is offline   Reply With Quote
Old 08-09-2007, 07:51 PM   #3
Tech Elite
 
GHETTOTEACHER's Avatar
 
Join Date: Feb 2007
Location: Philadelphia
Posts: 2,162
Default

On 28's the JP2 or JP3 work great. JP2 is a high end. JP3 is a low/High pipe. 28 have enough torque so a high end pipe works great. Last year, I found out the hard way. I had a JP1 on my 728 and I had great low to mid, but had no high. I swapped to the JP2 and everything was there! Life is good and I could run the entire powerband of that motor. My 928 runs great with the JP2. JP1's work great on 21's.

If you can get a matched manufactuers pipe, I would recomend that.
__________________
Herolin <---Traded my Airtronics for an Ipad and Laptop...
Soon to be GHETTOPRINCIPAL..
GHETTOTEACHER is offline   Reply With Quote
Old 08-09-2007, 08:28 PM   #4
Tech Master
 
sir miles's Avatar
 
Join Date: Jun 2007
Posts: 1,476
Trader Rating: 23 (100%+)
Default

May i ask what OS.28 engine is that?
__________________
gaining momentum!
sir miles is offline   Reply With Quote
Old 08-09-2007, 08:40 PM   #5
Tech Elite
 
Jason Halvorson's Avatar
 
Join Date: Apr 2007
Location: Grand Forks ND
Posts: 3,955
Trader Rating: 22 (100%+)
Send a message via AIM to Jason Halvorson Send a message via MSN to Jason Halvorson
Default

http://www.amainhobbies.com/product_...ducts_id/14929 there you go...
Jason Halvorson is offline   Reply With Quote
Old 08-09-2007, 09:41 PM   #6
Tech Adept
 
PRScustom's Avatar
 
Join Date: Jul 2007
Posts: 150
Trader Rating: 5 (100%+)
Default

Yes that is the correct engine. I was thinking about the JP-2 for the same reason mentioned above about the torque. I had a v-spec in my buggy and since it had so much bottom end I used the JP-2 to keep the bottom end the same and increase the top end. It worked great with the v-spec and had a ton of power all across the board. I was thinking the same would hold true with the .28. It should have a ton of bottom end and need a little help on the top end. Any other suggestions? One sight I read was a statement from O.S. that says the Mark Pavidis edition pipe is the perfect choice but I can't find it anywhere.
PRScustom is offline   Reply With Quote
Old 08-09-2007, 09:55 PM   #7
Tech Master
 
khoo's Avatar
 
Join Date: Feb 2007
Location: Along Equator
Posts: 1,266
Trader Rating: 1 (100%+)
Default

Quote:
Originally Posted by PRScustom View Post
Yes that is the correct engine. I was thinking about the JP-2 for the same reason mentioned above about the torque. I had a v-spec in my buggy and since it had so much bottom end I used the JP-2 to keep the bottom end the same and increase the top end. It worked great with the v-spec and had a ton of power all across the board. I was thinking the same would hold true with the .28. It should have a ton of bottom end and need a little help on the top end. Any other suggestions? One sight I read was a statement from O.S. that says the Mark Pavidis edition pipe is the perfect choice but I can't find it anywhere.
I think Mark uses the OS 2060 tuned pipe. Fantastic pipe with the V Spec
khoo is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
WTB .21 engine/pipe Allumina R/C Items: Wanted to Buy 1 07-19-2008 07:40 AM
This is the new Ninja MR 21 B01A engine with Ninja 2053 pipe and header. The engine h SmoothB R/C Items: For Sale/Trade 7 06-21-2007 09:56 AM
mugen mst1 with engine and pipe f/t for 1/8 buggy engine tony montana R/C Items: For Sale/Trade 5 08-22-2006 03:52 PM
New CEN NX-26 engine / pipe Lowrance R/C Items: For Sale/Trade 0 03-03-2006 01:00 PM
*~*~ OB4 (New Engine, Pipe Ect) ~*~* serpent 973 R/C Items: For Sale/Trade 2 03-18-2002 05:16 PM



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 09:00 PM.


Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net