Official AE RC18 Thread! - Page 32

bugsee2 · 04-25-2007, 11:18 PM

what servo saver are you using with this servo

ProudSavageOwnr · 04-26-2007, 01:22 AM

Quote:

Originally Posted by bugsee2

what servo saver are you using with this servo

wat servo?

bugsee2 · 04-26-2007, 10:57 AM

ko pds 30194 micro servo

pinoyboy · 04-26-2007, 05:01 PM

for those that compete off road, what are some good off road tires? I keep seeing people put 1/10 wheels on, is that for looks, or will those actually hook better in the dirt?

Mr.Modder · 04-26-2007, 11:40 PM

Quote:

Originally Posted by pinoyboy

for those that compete off road, what are some good off road tires? I keep seeing people put 1/10 wheels on, is that for looks, or will those actually hook better in the dirt?

onroad touring car wheels are used for onroad....

wont work offroad, if u want some offroad tyres get some aggressive looking stuff, not bowties, i got some realy aggressive ones that work realy well on everything except wet road and are virtually new and are mounted on alloy rims, full alloy and weigh practically nothing

take a look on here

http://www.rctech.net/forum/australia-sale-trade/160343-brushless-motors-motor-cooler-alloy-rims-mini-inferno-spares-boat-stuff-rxs-post3247630.html

theyre original for a mini inferno buy i also include 6-7 hex's that will work on the rc18t, i had em mounted on my rc18t n theyre realy nice

ercwhtsd · 05-01-2007, 09:46 AM

Quote:

Originally Posted by MikeR

Nothing you can do about that- all motors will get a little warm. It's when it starts hitting 160deg F that you might get worried.

I ended up taking both of the cobalts out after mine dead before an oval race this past weekend, we just cant' semm to find a ratio that will keep them under 150. When I took it apart the solder had actually melted off the com and spun inside the can. The stock 370 I put back in it ended up taking TQ for a oval race with 6.1 sec laps with temps barely hitting 110.

chris_mtb · 05-02-2007, 03:26 AM

yessss i got a rc18b i wanna race it i hav a mamba and previous racing with minis is there anything else i need

Mr.Modder · 05-06-2007, 03:47 AM

guys has anyone run a wraith 7k with 4 cell lipo in their rc18t? i just ordered that setup n shoud be ehre anyday.......cant wait!

Bermbuster · 05-06-2007, 06:18 AM

Quote:

Originally Posted by Mr.Modder

guys has anyone run a wraith 7k with 4 cell lipo in their rc18t? i just ordered that setup n shoud be ehre anyday.......cant wait!

hope you have spare parts.......

pinoyboy · 05-06-2007, 06:32 AM

I heard the shaft in the Wraith is weak point when doing 4 cell lipo. If your doing speed runs, it might break.

GhostFaceKilla · 05-06-2007, 09:39 AM

It for sure is prone to break if your dremeling notches into the shaft.

Mr.Modder · 05-07-2007, 12:03 AM

dont think i will n if i do i got spares, spur spurs al i need, wraith should i hold up i only grinded like a TINY notch n i mean tiny, dosnt even affect it at all

chris_mtb · 05-07-2007, 12:39 AM

i got the rc18 recently and put my mamba sport in it
now it doesnt go very fast like stock would prob keep up with is i want to know if i need better batteries i hav one stock associated and one intellect 1200

gashuffer · 05-07-2007, 10:18 AM

Li-po and a better mamba, competition or higher and you will be super fast.

admoc · 05-07-2007, 06:29 PM

If possible could someone povide me with some advice or personal experiences with what I could expect with the following battery configuration. I am looking at getting the Apogee Magnum 3-Cell 1500 mAh Li-Mn Battery Pack or if there is a better option.

I will be running it in a RCFT18T with a Mamba-25 and CM-2080 Competition X Motor (8000Kv).

Thanks in advance