R/C Tech Forums

Go Back   R/C Tech Forums > Members List

Casper Casper is offline

Tech Prophet

Visitor Messages

Showing Visitor Messages 1 to 10 of 87
  1. bubbaslash
    04-12-2017 05:06 PM - permalink
    bubbaslash
    Hi Casper. There's a thread "been out for a while and have some questions". Someone was asking about parts compatibility between his MIP 10SCTE and the 3.0. I'm not knowledgeable about the new truck, and I thought you could help him since you've worked on the evolution of the truck over the years.
    Thanks,
    John
  2. Kass
    08-17-2016 01:06 PM - permalink
    Kass
    Casper. Im a bit nee to 17.5 buggy and just bought an exotek alum 22 2.0 with a 3 gear. Can u plz give me a setup for indoor clay high bite? Thank u
  3. Casper
    04-16-2014 09:46 AM - permalink
    Casper
    I would go with the std Dunford setup as a great base for the SCTE 1.0.

    http://www.losi.com/ProdInfo/Files/L...ford-02_12.pdf

    Motor Sensored start much better. Depending on how serious your racing is it may not matter all that much to you. I strongly believe in Tekin motors and ESC's but they are not the cheapest options. Guys have had good luck with the hobby wing stuff but you don't get the support with those if you do have an issue. There are lots of options out there.
  4. Mike1977
    04-16-2014 07:28 AM - permalink
    Mike1977
    hello I am looking to get back in the racing I have a scte the original.

    I mainly like to run on dirt track I have a small 80x40 track at my house.. also looking to go to offroad dirt tracks some are big some are small. I'm not looking to change the whole car around every track just looking for a good base setup.

    #1 on my diff fluids what is a good all around out door dirt set up?
    #2 same question but for the shocks
    #3 as of now I have a castle mamba max pro with the 3800 4 pole motor which seemed ok back when I was into it. I need a motor for another car which I could use the 3800 in that and get a new one for the scte truck what would you recommend as a inexpensive motor? is the sensered motors that much better?
    basically I'm trying go over the whole truck once since it has been sitting and I know its needs attention.
    thanks for any info you can give me.
    Mike
  5. Casper
    04-08-2014 11:45 AM - permalink
    Casper
    The bearings can be very tight on the case. keep pressing but trying to only push on the inner race if you can. They will go on.
  6. Kaw1000
    04-07-2014 10:22 PM - permalink
    Kaw1000
    I'm trying to rebuild diffs in a SCTE TEN. I bought the HD diff case. The problem is the bearings that go over out drives will not go all the way down diff case shaft. The diff will not fit in case because bearings off just a little...case number tlr332001 and outer bearings...12x18 losa6956 Thanks
  7. Casper
    04-07-2014 03:42 PM - permalink
    Casper
    Sorry not sure what a 22T-R conversion is? Is that Rear motor?

    My std Rear motor setup is on my web site. www.casper-rc.com For carpet I would work with a MM setup though.
  8. timw60
    04-07-2014 03:20 PM - permalink
    timw60
    Hello.
    I am putting the 22T-R conversion on my truck.
    What setup do you use for indoor clay med to high bite?

    The setup I have is for carpet.

    Thanks. Tim..
  9. Casper
  10. RustyRC
    03-24-2014 07:26 AM - permalink
    RustyRC
    whats profile settings on gen1 esc for tekin pro4 4600? outdoor track

About Me

  • About Casper
    Location
    Orange, Ca
    Occupation
    Mechanical Engineer
  • Signature
    TLR/Losi Team Driver
    TLR/Losi | Tekin | DE Racing | Spektrum | Exotek | JBRL | Kolor Koncepts | OC/RC |Sticky Kicks | Imagine It Graphics | Casper-RC.com
    TLR 22 4.0 SR, TLR 22T 3.0 (laydown), TLR 22-4 2.0, Spektrum DX6R

    WWW.CASPER-RC.COM TLR and Tekin setups

Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: 11-22-2017 04:06 PM
  • Join Date: 08-03-2004
  • Referrals: 3

Friends

Showing Friends 1 to 10 of 30

All times are GMT -7. It is currently 03:24 PM.


Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net