Ask Mike Blackstock Trinity ,Rcamerica, Team Xray Edition..
#196
Mike on your 007 set up sheet it says shims in front 2.65 and shims in rear 33. im guessing its suppost to be 3.3? And then for the front you add one of the gold 1.15 shims? What about the rear? So that would give you inboard toe in up front? Any help will be appreciated.
#197
Tech Master
iTrader: (35)
Originally Posted by TimmyMontoya
Mike on your 007 set up sheet it says shims in front 2.65 and shims in rear 33. im guessing its suppost to be 3.3? And then for the front you add one of the gold 1.15 shims? What about the rear? So that would give you inboard toe in up front? Any help will be appreciated.
#198
Tech Elite
iTrader: (89)
mike--- i am to curious about the front shims as well. how does this inboard toe in effect the handling...also since you are running the 3mm on the inside front and rear, is that why your front and rear roll centers are in the outer lower holes to keep the geometry the same ?
thanks!
thanks!
#199
Tech Champion
iTrader: (3)
Join Date: Mar 2003
Location: Peoples Republic of Northern Virginia
Posts: 5,682
Trader Rating: 3 (100%+)
HELP!!!!!!!!!!!!!!!!!!
Since no one has replied to the thread I started on this....
Has anyone else have problems with these pinions?
I've chewed up 2 116 spurs using 2 different one and a friend of mind chewed up another one this last Saturday. Both cars are X-ray T2, ( 16, 24 and 28 was being used on 116 robinson spur gears ). I went back to the Steel pinion and did not have any peoblems. I also had 2 experience racers take a look at the gear mesh and made sure the motor was tight before I ran it. The last one was a new spur and it ran 8 feet before it chewed it up. There is a little side play with the spur but everyone else has the same play as mine....
I got these from Stormer Hobbies ( I don't believe this is a stormer hobby issue ) and the production information provided:
Part Number: PRS6428
Pinion Gear-28 tooth, 64 pitch aluminum
These ultra-precise pinion gears are machined perfectly round from light 6061 aluminum, then hard teflon coated black. Eight additional lightening holes have been added to reduce the rotating mass. These pinion gears also take the large .062" tip wrench that are used on your 4 x 40mm button head screws.
Has anyone else have problems with these pinions?
I've chewed up 2 116 spurs using 2 different one and a friend of mind chewed up another one this last Saturday. Both cars are X-ray T2, ( 16, 24 and 28 was being used on 116 robinson spur gears ). I went back to the Steel pinion and did not have any peoblems. I also had 2 experience racers take a look at the gear mesh and made sure the motor was tight before I ran it. The last one was a new spur and it ran 8 feet before it chewed it up. There is a little side play with the spur but everyone else has the same play as mine....
I got these from Stormer Hobbies ( I don't believe this is a stormer hobby issue ) and the production information provided:
Part Number: PRS6428
Pinion Gear-28 tooth, 64 pitch aluminum
These ultra-precise pinion gears are machined perfectly round from light 6061 aluminum, then hard teflon coated black. Eight additional lightening holes have been added to reduce the rotating mass. These pinion gears also take the large .062" tip wrench that are used on your 4 x 40mm button head screws.
#202
Sorry for being absent for so long.. I am back geting ready for the novak race .....
Scott... Wow that is old... Wish i was that skinny now ...
Mike
Scott... Wow that is old... Wish i was that skinny now ...
Mike
#203
TimmyMontoya .. It was supposed to be 3.0 in the rear.. I was running alittle bit of front arm sweep....
Nova F1 Racer.. I have never had any problems with the 64 pitch spurs ... maybe you got a bad batch or something contact teamxray or rcamerica.
darryl... Glad i could help ya ....
Mike
Nova F1 Racer.. I have never had any problems with the 64 pitch spurs ... maybe you got a bad batch or something contact teamxray or rcamerica.
darryl... Glad i could help ya ....
Mike
#205
Tony... I am not 100% sure.. I think they may still have some parts etc.. I do know they will be selling the CRC car with Frank ....
Mike
Mike
#206
Tech Champion
iTrader: (3)
Join Date: Mar 2003
Location: Peoples Republic of Northern Virginia
Posts: 5,682
Trader Rating: 3 (100%+)
Originally Posted by Mike Blackstock
TimmyMontoya .. It was supposed to be 3.0 in the rear.. I was running alittle bit of front arm sweep....
Nova F1 Racer.. I have never had any problems with the 64 pitch spurs ... maybe you got a bad batch or something contact teamxray or rcamerica.
darryl... Glad i could help ya ....
Mike
Nova F1 Racer.. I have never had any problems with the 64 pitch spurs ... maybe you got a bad batch or something contact teamxray or rcamerica.
darryl... Glad i could help ya ....
Mike
#207
nova.. Glad you found the problem.. And sorry i was so late to respond....
Mike
Mike
#208
Tech Champion
iTrader: (3)
Join Date: Mar 2003
Location: Peoples Republic of Northern Virginia
Posts: 5,682
Trader Rating: 3 (100%+)
Originally Posted by Mike Blackstock
nova.. Glad you found the problem.. And sorry i was so late to respond....
Mike
Mike
#209
Guest
hey mike i notice rc america and x ray are no longer in you sig. i was wondering if you are planning on going to a corally car or a associated ?
#210
Hey Mike what car will you be driving at the Florida Winternats?