Serpent Project 4-X
|
|||
#226
Tech Champion
iTrader: (42)
I love mine! It's 'tricky' to setup because the platform is new and there are fewer setup sheets for one to copy.
Once you get a hang of it though, the car is great.
What worries is a little now is that Team Serpent don't seem to be having much luck with the car on the intl competition level. They just did poorly in Thailand. I worry it will suffer the same fate as the SRX4 (original innovative design) and give way to the 'standard' design like the SDX4.
Once you get a hang of it though, the car is great.
What worries is a little now is that Team Serpent don't seem to be having much luck with the car on the intl competition level. They just did poorly in Thailand. I worry it will suffer the same fate as the SRX4 (original innovative design) and give way to the 'standard' design like the SDX4.
I owned an Xray T4 prior to this car and it worked very well. Almost set and forget. My first packs on the 4x I could tell there was a definitive difference in handling. The 4x just handled the entry and exit of corners so much better. Why...I'm not sure, but I was more comfortable with the 4x.
Now that a lot of guys are running we are seeing more and more setups. If you are running black CRC carpet just copy one of Paul Ciccerllos/Jeff Dayger setups and you should be good to go
I'd also follow the Facebook page if you use FB. Way more Serpent users active on there.
https://www.facebook.com/groups/SerpentProject4X/
#227
Picked one up! Just can't find the starter kit in the US.
#229
#231
Any Starter kits in the US, anyone, Bueller?
#233
Do they make protective film anymore for chassis' or maybe a recommended spray to minimize wear/marring from asphalt?
The upper and lower arms, and hubs are all symmetrical/compatible front and rear correct? Now, I haven't looked, but are all the parts symmetrical, from left to right?
#234
Also, is 111oz tq./w a .13 sec. speed servo enough power for this car? I don't need a ton of speed since I seem to overreact.
#235
Tech Fanatic
iTrader: (7)
Which O-Rings and Springs? I'm pretty sure it's "HD Ozite Carpet" something like that. Probably will try asphalt too.
Do they make protective film anymore for chassis' or maybe a recommended spray to minimize wear/marring from asphalt?
The upper and lower arms, and hubs are all symmetrical/compatible front and rear correct? Now, I haven't looked, but are all the parts symmetrical, from left to right?
Do they make protective film anymore for chassis' or maybe a recommended spray to minimize wear/marring from asphalt?
The upper and lower arms, and hubs are all symmetrical/compatible front and rear correct? Now, I haven't looked, but are all the parts symmetrical, from left to right?
Protective, no ideas.
Yes, everything is symmetric.
#236
Tech Elite
iTrader: (101)
Which O-Rings and Springs? I'm pretty sure it's "HD Ozite Carpet" something like that. Probably will try asphalt too.
Do they make protective film anymore for chassis' or maybe a recommended spray to minimize wear/marring from asphalt?
The upper and lower arms, and hubs are all symmetrical/compatible front and rear correct? Now, I haven't looked, but are all the parts symmetrical, from left to right?
Do they make protective film anymore for chassis' or maybe a recommended spray to minimize wear/marring from asphalt?
The upper and lower arms, and hubs are all symmetrical/compatible front and rear correct? Now, I haven't looked, but are all the parts symmetrical, from left to right?
Steve
#237
Where can I order these parts? I can't find shops with any stock.
Also, which O-Rings, the shock O-Rings?
Did you all see my servo post? Sufficient, mediocre, weak?
Also, which O-Rings, the shock O-Rings?
Did you all see my servo post? Sufficient, mediocre, weak?
#239